Knowledge

HEB 1000x300x19x36 S355JR Hot Rolled Wide Flange Beam: Section, Material and Fabrication

May 15, 2025 Leave a message

What HEB 1000 x 300 x 19 x 36 Means

HEB 1000 x 300 x 19 x 36 is an ultra-heavy hot rolled wide flange H-beam of the European profile system. The four numbers are read in a fixed sequence: section height 1000 mm, flange width 300 mm, web thickness 19 mm and flange thickness 36 mm. The nominal mass of the profile is 314 kg per metre, which places it in the heaviest class of sections rolled for building and bridge work.

Dimensions follow the European table of hot rolled I and H sections, while shape and dimensional tolerances are governed by EN 10034. Because the section is symmetric about both axes, it behaves in the same way in positive and negative bending, which simplifies the design of continuous and cantilever members.

S355JR Material Properties

The beam is rolled in S355JR to EN 10025-2, a non-alloy structural steel with a minimum yield strength of 355 MPa for the thinnest reference thickness, a tensile range of 470-630 MPa and a guaranteed Charpy V impact energy of 27 J at +20 °C. Yield strength falls in steps as the reference thickness grows:

Thickness t (mm) Yield strength min (MPa)
t ≤ 16 355
16 < t ≤ 40 345
40 < t ≤ 63 335
63 < t ≤ 80 325
80 < t ≤ 100 315
100 < t ≤ 150 295
150 < t ≤ 200 285
200 < t ≤ 250 275
250 < t ≤ 400 265

Minimum elongation is 22 % up to 40 mm, 21 % from 40 to 63 mm and 20 % above 63 mm. Impact toughness classes in EN 10025-2 are defined by test temperature rather than by a different strength level: JR is tested at +20 °C, J0 at 0 °C and J2 at -20 °C, each with a 27 J minimum average value. Specifying J0 or J2 therefore raises the low temperature security of the same strength class at a modest cost.

Chemical Composition

Element max % C Si Mn P S N Cu
S355JR 0.24 0.55 1.60 0.035 0.035 0.012 0.55
S355J0 0.20 0.55 1.60 0.030 0.030 0.012 0.55

The low carbon and moderate manganese content, together with the fine grain practice used for the grade, keep the steel weldable with conventional consumables. For welded heavy sections a carbon equivalent limit is agreed between buyer and supplier; a value around 0.47 % is a practical reference for S355JR material of this size class, and higher strength or thicker sections are ordered with a tighter value.

Section Performance

The 1000 mm depth provides a long lever arm between the flanges, so a large part of the bending moment is resolved as a pair of forces in the flanges. The 36 mm flange carries that force without local buckling, while the 19 mm web transfers shear and stabilises the flanges. The result is a section that develops a very high bending resistance and bending stiffness for the mass of steel used, and that tolerates the concentrated forces introduced by crane rails, heavy column bases or bearing plates.

Deep section: high second moment of area and section modulus for bending about the strong axis

Heavy flange: good local buckling resistance and simple welded or bolted splicing

Symmetric shape: equal capacity in sagging and hogging bending

Straight parallel flanges: accurate alignment for bearing plates, rail fixings and bolted connections

Typical Applications

Main girders and box-section beams of long span and cross-sea bridges

Outer frame columns and seismic bracing of super high-rise buildings

Track beams of heavy port cranes and support frames of mining equipment

Support systems of energy facilities, including containment and tank dome frames

Transfer girders and heavily loaded industrial platforms

Fabrication, Welding and Protection

Preheating to at least 120 °C is applied when the wall thickness exceeds 35 mm, with interpass temperature held in the 200-250 °C range during multi-pass welding.

Welding consumables matched to the 355 MPa class are used, and heat input is controlled to limit the width of the heat affected zone.

Bolted connections use the high strength bolting system to EN 14399; holes are drilled rather than punched in heavily loaded joints.

For marine or coastal service an epoxy zinc-rich primer with a dry film thickness of at least 120 µm is a common protection, while hot dip galvanizing suits inland outdoor structures; both processes require clean, salt-free surfaces for good adhesion.

Cut ends and weld areas are re-coated after fabrication so that no bare steel is left in a corrosive environment.

Frequently Asked Questions

Q: What do the four numbers in HEB 1000 x 300 x 19 x 36 mean?
They are section height 1000 mm, flange width 300 mm, web thickness 19 mm and flange thickness 36 mm, giving a nominal mass of 314 kg per metre.

Q: Which standard covers the material?
The material is rolled to EN 10025-2 in grade S355JR, and dimensional tolerances for the profile follow EN 10034.

Q: What is the minimum yield strength of the section?
355 MPa for a reference thickness up to 16 mm, decreasing in steps to 265 MPa for reference thickness between 250 and 400 mm.

Q: Is S355JR suitable for low temperature service?
Its impact test is carried out at +20 °C. For structures that must remain tough in cold weather the J0 class at 0 °C or the J2 class at -20 °C is specified instead.

Q: Can the beam be hot dip galvanized?
Yes. Galvanizing is widely used for outdoor structures; the surface must be free of oil, scale and salt, and cut edges should be dressed before dipping.

Q: How is the beam delivered?
Hot rolled with mill test certificates to EN 10204 3.1, normally in fixed lengths, and cut to project length before shipment when required.

Send Inquiry