When purchasing Q390B steel plates, the Mill Test Certificate (MTC) or Quality Certificate is the legal document that guarantees the material conforms to the ordered specifications (GB/T 1591-2018 and any supplemental requirements). It must be complete and verifiable.

Here are the key inspection items the certificate must include:
1. Mandatory Information (Header & Traceability)
Certificate Number: Unique ID for traceability.
Standard & Grade: Explicitly stated as GB/T 1591-2018, Q390B.
Manufacturer's Name & Logo: Identifies the producing mill.
Purchase Order/Contract Number: Links the certificate to your specific order.
Heat Number/Batch Number: The most critical traceability code. All test results are tied to this unique melt identification.
Plate Identification: Serial numbers, dimensions (thickness, width, length, and quantity).
2. Chemical Composition Analysis
The report must list the actual measured values for all specified elements, typically from a sample taken during the melt. Key items to verify:
Standard Elements: C, Si, Mn, P, S. Ensure P and S are at or below the strict limits (P≤0.030%, S≤0.030%).
Micro-alloying Elements: V, Nb, Ti (if added). The actual amounts used are critical for meeting strength.
Optional/Residual Elements: Cu, Cr, Ni, Mo, etc., if specified or limited.
Calculated Value: Carbon Equivalent (Ceq). This should be calculated and reported, as it directly impacts weldability. For Q390B, a typical Ceq (IIW) might be 0.44-0.49%.
3. Mechanical Property Test Results
Results must correspond to the specific thickness range of the delivered plates.
Tensile Test:
Yield Strength (ReH) – Actual Value: Must meet or exceed the standard's minimum for its thickness (e.g., ≥390 MPa for t≤16mm, ≥370 MPa for 16<t≤40mm, etc.).
Tensile Strength (Rm) – Actual Value: Must fall within the specified range (490-650 MPa).
Elongation at Break (A) – Actual Value: Must meet or exceed the minimum (≥19% for t≤40mm, longitudinal).
Impact Toughness Test (Charpy V-Notch):
Test Temperature: Must be +20°C for grade B.
Specimen Orientation: Usually transverse.
Impact Energy – Three Individual Values & Average: Each value and the average must be ≥ 34 Joules.
4. Technological Property Tests (If Specified)
Bend Test Results: Type of test (e.g., 180° bend) and outcome (e.g., "no cracks observed").
Flattening Test/Flaring Test: For tubular products.
5. Additional/Specific Requirements
If the purchase order included supplemental requirements, the certificate must provide proof of compliance:
Ultrasonic Testing (UT): Report and adherence to a specified acceptance level (e.g., GB/T 2970, Class I or II).
Through-Thickness (Z-direction) Testing: Z15, Z25, or Z35 property results if ordered to prevent lamellar tearing.
Non-Destructive Testing (NDT): Records of any other NDT performed.
Heat Treatment Condition: Confirm "as-rolled" or other specified condition.
6. Inspector's Stamp and Date
Official stamp/signature of the mill's quality department.
Date of issue.
Red Flags & Verification Steps
Thickness-Property Mismatch: Ensure the reported yield strength matches the minimum for the specific plate thickness, not just the nominal 390 MPa.
Missing Heat Number: Never accept a certificate without a heat/batch number. It is untraceable.
"Typical Values" or Ranges: The certificate must report actual tested values, not just "meets standard."
Third-Party Certificates: Certificates from traders are not valid unless they are original documents from the mill or certified true copies. Always request the mill's original certificate.
Independent Verification: For critical projects, conduct third-party laboratory testing on samples from the delivered plates to verify the certificate's accuracy.
Summary Checklist for the Procurement/QC Engineer
Heat/Batch Number present and matches plate markings.
Standard & Grade: GB/T 1591-2018, Q390B.
Chemical Composition: All elements reported, with P, S ≤ 0.030%.
Mechanical Properties: Actual values for Yield (ReH), Tensile (Rm), Elongation (A) that satisfy thickness-dependent requirements.
Impact Test: Three values and average at +20°C ≥ 34 J.
Supplemental Tests: Reports for UT, Z-direction, etc., if ordered.
Inspector's Stamp/Signature and date.
By meticulously checking these items, you ensure the Q390B material is as specified, traceable, and suitable for its intended structural purpose, thereby mitigating the risk of using substandard steel.

