Knowledge

What Is the Difference Between an H-Beam and an I-Beam

Oct 17, 2023 Leave a message

Cross-Section Geometry Is the Real Difference

H-beams and I-beams are both hot-rolled structural sections, but the relationship between web height and flange width is different, and that single ratio decides where each section can be used. An I-beam has a relatively high, thin web and narrow flanges whose inner faces are tapered, so the section reads as a capital I. An H-beam has flanges that are wide, thick and parallel-faced, so the section reads as an H and the flange area is distributed far from the neutral axis.

The consequence is that an H-beam develops a large section modulus about its strong axis and also a useful section modulus about the weak axis, whereas an I-beam is efficient in one direction only. The parallel flange of an H-beam also gives a flat bearing surface for bolted end plates and for beams framing into a column face.

Designations and Dimensional Standards

Designation Height (mm) Flange width (mm) Web thickness (mm) Flange thickness (mm) Mass (kg/m)
IPE 200 200 100 5.6 8.5 22.4
IPE 300 300 150 7.1 10.7 42.2
HEB 200 200 200 9.0 15.0 61.3
HEB 300 300 300 11.0 19.0 117.0

European parallel-flange sections are designated IPE, HEB and HEM, with dimensions listed in EN 10365 and delivery conditions in EN 10025-2. Tapered-flange I-beams are still produced to Japanese and American dimensional practice and to ASTM A6/A6M section lists, where they appear as S shapes. Buyers should quote the designation plus the tolerance standard, not the trade name alone, because the same nominal height exists in both families with very different mass.

Load Behaviour, Torsion and Stability

An I-beam offers a high strength-to-mass ratio in simple bending and good stiffness in the plane of the web, but its torsional resistance is low because the open, thin-web section has little St. Venant stiffness and warps freely. An H-beam, with its wide flange, resists lateral-torsional buckling far better, so it can be used at longer unsupported lengths or with fewer lateral restraints. For a given load, an H-beam frequently allows a longer span and fewer columns, which lowers the cost of the connections and the foundations even though the steel itself costs more per metre.

Where the member is loaded through the web and the load does not pass through the shear centre, both sections twist. In that case the design answer is either to brace the compression flange, to add stiffeners, or to move to a closed box section.

Applications and Practical Span Limits

Tapered-flange I-beams are common in short-span floor and roof framing, elevator and crane support frames, trailer and tramway chassis, and light bridge decking. Parallel-flange H-beams are the default for building frames, long-span roof structures, heavy crane girders, bridge girders and offshore support structures, and for columns because the wide flange gives a stable compression element in both directions.

Cost, Availability and Procurement

An H-beam costs more per tonne but often less per unit of load carried, because less steel and fewer supports are needed. Procurement should compare on a delivered basis: section mass per metre, cutting and drilling effort, connection detail (end plates or fin plates), and the surface treatment demanded by the specification, such as hot-dip galvanizing to EN ISO 1461.

Frequently Asked Questions

Q: What is the main difference between an H-beam and an I-beam?
A: Flange geometry. An H-beam has wide parallel flanges and resists bending in both directions; an I-beam has narrow tapered flanges and works efficiently in one direction only.

Q: Can an I-beam be replaced by an H-beam of the same height?
A: Usually yes, but not by height alone. Compare section modulus, second moment of area, mass and connection geometry, because an H-beam of the same height is much heavier.

Q: Which section is better for torsion?
A: The H-beam, because its flange mass is concentrated far from the web. Neither open section is good in torsion; a closed box is far superior.

Q: Are H-beams and W-beams the same thing?
A: In American practice the wide-flange shape is listed as a W shape, and it corresponds to the European parallel-flange H-beam family. Both are covered by similar dimensional tables but different standards.

Q: What is the practical span limit for an I-beam?
A: I-beams are normally limited to short and medium spans with frequent lateral restraint. Beyond that, lateral-torsional buckling governs and an H-beam becomes the more economical choice.

Send Inquiry