A parallel flange channel, commonly shortened to PFC, is a hot-rolled structural steel section with a C-shaped cross-section in which the two flanges are parallel to each other and the inner faces are square to the web. It is one of the most widely used steel beam sections in general construction because it delivers a stiff, load-bearing member that can be bolted or welded flat against another surface on three sides.
What a Parallel Flange Channel Looks Like
The section consists of a vertical web with a flange projecting at 90° at each end, giving the familiar C or U profile. In a genuine parallel flange channel the flanges are the same thickness along their length and their inner faces are square, not tapered. This is the key difference from the older taper flange channel, often designated UPN or C, whose sloping inner flange faces complicate bolted connections.
Parallel flanges with square inner faces, so nuts and washers seat squarely.
A pronounced C-shaped cross-section that is stiff about the axis of the web.
Hot-rolled from structural steel, so the section thickness and shape are uniform.
Available in a graduated range of depths and masses to suit different spans and loads.
Typical PFC Size Range
Parallel flange channels are produced in a graduated series, usually described by depth, flange width and mass per metre. The smallest standard sizes start around 100 mm deep with a 50 mm flange, and the largest reach roughly 430 mm deep with a 100 mm flange.
| Designation (depth × flange width) | Nominal depth | Nominal flange width | Typical role |
|---|---|---|---|
| PFC 100 × 50 | 100 mm | 50 mm | Purlins, small lintels, framing |
| PFC 150 × 75 | 150 mm | 75 mm | Floor joists and edge beams |
| PFC 200 × 75 | 200 mm | 75 mm | General floor beams |
| PFC 260 × 75 | 260 mm | 75 mm | Medium-span floor beams and lintels |
| PFC 300 × 90 | 300 mm | 90 mm | Long-span floor beams |
| PFC 380 × 100 | 380 mm | 100 mm | Heavy floor beams and edge members |
| PFC 430 × 100 | 430 mm | 100 mm | Heavy-duty transfer and crane members |
Because the mass per metre increases with wall thickness as well as depth, two channels of the same depth can differ substantially in capacity. Design tables published by the rolling mill give the exact area, second moment and mass for each designation, and those values should always be used for design rather than the depth alone.
Grades and Standards
Parallel flange channels are normally rolled in weldable structural steel grades such as S275JR and S355JR to EN 10025-2, or in the equivalent general structural class represented by ASTM A36. Dimensional tolerances for European channels are covered by EN 10279, with EN 10034 applying to European I and H sections of the same family. Both the grade certificate and the dimensional certificate should accompany a structural delivery.
Why the Parallel Flange Matters
Square, parallel flanges are not a cosmetic detail. They let a channel be bolted cleanly to a plate or to another member with normal bolts and washers, and they allow two channels to be placed back to back or toe to toe with a consistent gap for a welded or bolted connection. In tapered flange channels the sloping inner faces force the use of tapered washers, which increases cost and reduces the reliability of slip-critical joints. The parallel flange is the reason the PFC became the default channel in modern fabrication.
Where Parallel Flange Channels Are Used
The C-shape is at its best where a beam has to sit flush against a wall, slab edge or tank shell, or where one flat face is needed for a bolted connection. Typical applications include floor beams, lintels over openings, purlins and side rails, edge members of floors and roofs, mezzanine framing, trailer and chassis frames, machine bases, and temporary works such as props and bracing.
As a load-bearing element a channel is strongest about the axis perpendicular to its web and much weaker about the other axis, and it twists more readily than a wide-flange beam of the same depth. It is therefore normally used with the web vertical, laterally restrained along its span, or in a pair to balance the section.
Frequently Asked Questions
Q: What does PFC stand for?
Parallel flange channel, a hot-rolled C-shaped structural section whose flanges are parallel with square inner faces.
Q: How does a PFC differ from an ordinary channel?
An ordinary taper flange channel has sloping inner flange faces, while a PFC has parallel flanges and square inner faces that accept standard bolts and washers.
Q: What sizes are available?
The standard series runs from about 100 × 50 mm up to roughly 430 × 100 mm in depth and flange width, with several masses at each depth.
Q: What steel grades are used?
S275JR and S355JR to EN 10025-2 are the common structural grades, and the general structural class represented by ASTM A36 is also widely available.
Q: Where are parallel flange channels used?
Floor beams, lintels, purlins and side rails, floor and roof edge members, mezzanine framing, chassis members and machine bases.
Q: Is a PFC as strong as a wide-flange beam of the same depth?
No. A channel is weaker in bending about its major axis and twists more easily, so it is usually chosen for edge beams and connections rather than long, heavily loaded spans.

