Knowledge

W27x94 Hot-Dip Galvanized H-Beam: Specifications and Structural Use

May 23, 2025 Leave a message

What the W27x94 Designation Means

W27x94 is an American standard wide flange H-beam covered by ASTM material specifications such as A36 and A572 Grade 50. In the W designation the first figure is the nominal web depth in inches and the second is the unit mass in pounds per linear foot, so a W27x94 section has a nominal depth of 27 inches and weighs about 94 pounds per linear foot, equivalent to roughly 140 kg per metre. Its flange width is about 10 inches.

The hot-dip galvanized (HDG) version is the same rolled section taken through a galvanizing line, where cleaned steel is immersed in molten zinc so that a metallurgically bonded zinc-iron coating forms on the surface. Because the coating reaches the inside faces of the flanges and the web, protection is not limited to outer surfaces, which matters for purlins, brackets and roof frames that stay exposed for the life of the building.

Section Dimensions and Delivery Range

Parameter Value or range
Web height 27 in (about 686 mm)
Flange width 10 in (about 254 mm)
Web thickness 12.4 mm
Flange thickness 18.9 mm
Unit mass about 140 kg/m (94 lb/ft)
Lengths 6 m, 8 m, 9 m, 11 m, 12 m or to order
Model range H100×100 to H900×300
Web width range 100–900 mm
Flange width range 100–300 mm
Web thickness range 5–30 mm
Flange thickness range 5–30 mm

Non-standard lengths and section combinations in the same family can be rolled to order, so a frame can be detailed around a single depth class and still obtain the required moment capacity.

Materials and Mechanical Performance

Two grades dominate for this section:

ASTM A36 - a low-carbon structural steel with a carbon content of about 0.29%. It has good plasticity and welding behaviour. Typical values are a minimum yield strength of 250 MPa (36,000 psi) and a tensile strength of 400–550 MPa (58,000–80,000 psi).

ASTM A572 Grade 50 - a high-strength low-alloy steel with a minimum yield strength of about 345 MPa (50,000 psi) and a typical tensile strength of 450–655 MPa (65,000–95,000 psi), used where loads are heavier and a lighter section is wanted.

Typical elongation for these grades is around 20%, which allows a degree of deformation before failure, a useful property in seismic and impact-loaded structures. The symmetrical H cross-section gives the beam a high section modulus, so it carries a large bending moment for its weight and works well as a long-span member. That symmetry also provides equal stiffness about both principal axes, one reason H-sections are widely used in earthquake-prone regions.

Galvanized Compared with Black Sections

A black (bare) rolled section is normally painted or fire protected on site, and every cut edge or drilled hole has to be touched up. An HDG section carries a continuous zinc coating over the whole profile, including the inner fillets, and the zinc continues to protect small damaged areas by sacrificial action. For structural roofing, exposed framing and outdoor equipment supports this means a longer maintenance interval and less site work. Fabrication such as cutting and drilling is normally carried out before galvanizing, or the coating is repaired afterwards.

Typical Applications

Roof purlins, rafters and primary framing for industrial and warehouse buildings.

Beams and columns in industrial and civil buildings, including large-span workshops and high-rise frames.

Main girders and load-bearing members in bridge and highway construction.

Equipment frames, brackets and heavy machinery bases.

Exposed structures such as petrochemical plant supports, port facilities, ship frames and foundation works.

Frequently Asked Questions

Q: What does W27x94 mean?
The 27 is the nominal depth of the section in inches and the 94 is the unit weight in pounds per linear foot, about 140 kg/m; the flange width is about 10 inches.

Q: Is the galvanized coating applied to the whole section?
Yes. Hot-dip galvanizing covers the outer and inner faces of both flanges and the web, including the fillets, so hidden surfaces are protected as well.

Q: Which material grades are supplied?
ASTM A36 and ASTM A572 Grade 50 are the usual grades; the choice follows the design yield strength and the required weldability.

Q: How heavy is the beam per metre?
A W27x94 section weighs about 140 kg per metre, equivalent to 94 pounds per linear foot.

Q: Why choose a galvanized beam instead of a black one?
The zinc coating protects the entire profile and extends the maintenance interval in roofing, outdoor and corrosive-service structures, at the cost of a higher initial price.

Q: What lengths are available?
Common lengths are 6 m, 8 m, 9 m, 11 m and 12 m, with other lengths rolled to order.

Send Inquiry