An I-section puts material where bending stress is highest: the flanges carry most of the moment while the web resists shear. That shape is reached by one of two production routes, either hot rolling a one-piece beam or welding plate into a built-up section. The two routes are not interchangeable in every project, because the choice changes stiffness, connection detailing, fabrication lead time and total installed cost.
What a Single Rolled I-Steel Piece Is
A single rolled I-beam is formed by passing a heated bloom through a train of grooved rolls until the final profile is reached. The section is homogeneous, contains no weld metal, and is certified against one heat of steel. Standard rolled sizes are produced to dimensional tolerances such as EN 10034 or ASTM A6.
Continuous flange and web, so there are no weld seams to inspect.
Published section properties that designers can take directly from mill tables.
Fast availability in common depths from mill stock or service centres.
Straightforward bolted connections using standard cleats, end plates and fin plates.
Simple surface preparation before painting or galvanizing.
Typical rolled grades include S235JR, S275JR, S355JR and S355J2 to EN 10025-2, and ASTM A992 or A36 in the imperial system.
Applications Suited to Single Rolled Sections
Rolled members are the economical choice whenever the required moment capacity falls inside the standard size range and the span does not demand a custom depth. Load-bearing frames in buildings, floor beams, bridge stringers, crane runway supports, machine bases, mezzanine decks and conveyor gantries are all routine applications. Because the sections arrive ready to erect, site work is limited to cutting, drilling and bolting.
Where a stiff, quickly assembled member is required and the geometry is regular, a single rolled beam normally gives the lowest installed cost per tonne of steel. It is also easier to replace or adapt on site than a welded assembly, which matters in equipment that is retrofitted or relocated.
Welded I-Steel Parts and Where They Win
Welded, or built-up, I-steel parts are fabricated from plate by submerged arc welding, usually with a continuous fillet weld on each side of the web. The fabricator controls flange width, flange thickness, web thickness and depth independently, so the member can be tailored to the exact design moment, shear and buckling requirement.
| Feature | Single rolled I-steel piece | Welded I-steel part |
|---|---|---|
| Section properties | Fixed, taken from mill tables | Optimised for the load case |
| Depth range | Standard range only | Practically unlimited |
| Connection detailing | Standard bolted details | Free choice of flange and web plate |
| Lead time | Immediate to a few weeks | Dependent on fabrication slot |
| Cost driver | Mill price per tonne | Plate price plus welding labour |
Welded parts are favoured for long-span girders, heavy crane beams, bridge plate girders, columns with unequal flange demand, and members that need openings, stiffeners or tapered geometry that a rolled profile cannot provide.
Selecting the Right Form for the Project
Work through the criteria in order. First, check whether a standard rolled section satisfies strength, deflection and vibration limits; if it does, the rolled option is usually cheaper and faster. Second, check handling and transport limits, since a welded girder may need site splices to travel by road. Third, review connection complexity, because bolted rolled beams suit repetitive frames while welded plate girders suit one-off heavy structures. Fourth, consider corrosion protection, as welded assemblies present more weld toes, edges and internal corners to prepare and coat.
Quality Control for Welded Parts
The welded route concentrates risk in the weld, so fabrication control is essential. Weld procedure specifications should be qualified to ISO 15614-1 or ASME Section IX, welders and operators qualified to ISO 9606 or an equivalent scheme, and dimensional checks made after welding to confirm that distortion stays inside tolerance. Continuous fillet welds are inspected visually, and by ultrasonic testing where the detail is fatigue sensitive.
FAQ
Q: Can a welded I-steel part replace a rolled beam one for one?
Yes, provided the welded section matches or exceeds the required section modulus, moment of inertia and shear area, and the connections are re-checked against the new flange and web thicknesses.
Q: Which is cheaper, a rolled beam or a welded I-steel part?
A rolled beam is usually cheaper when a standard size works, because welding labour, plate handling and inspection are avoided. A welded part becomes economic when the design needs a non-standard depth or a heavier flange.
Q: Do bolted connections suit both forms?
Yes. Bolted details are the norm for rolled sections, and welded assemblies are usually supplied with shop-welded end plates or shear tabs so that site joints remain bolted.
Q: What grades are used for welded I-steel parts?
Plates to EN 10025-2, such as S355J2, or ASTM A572 Grade 50 and A709 grades for bridges, with matching filler metals that meet the same strength and toughness class.
Q: How is distortion controlled during fabrication?
By balancing the welding sequence on both sides of the web, using restrained jigs, limiting heat input, and straightening after the assembly has cooled.

