Knowledge

SS490 Steel H-Beam: Properties and Construction Applications

Feb 25, 2025 Leave a message

SS490 is a structural steel grade defined in the Japanese Industrial Standard JIS G3101, which covers rolled steels for general structure. H-beam sections produced from SS490 combine a minimum yield strength of 285 MPa with a tensile strength of 490 to 610 MPa, providing the load-carrying capacity required for demanding building and engineering structures. This article describes the material properties, section characteristics, and typical applications of SS490 H-beam.

Material Properties of SS490

SS490 belongs to the SS steel family in JIS G3101, which also includes SS330, SS400, and SS540. The minimum yield strength of SS490 is 285 MPa and the tensile strength is 490 to 610 MPa, which is higher than the widely used SS400 grade with a minimum tensile strength of 400 to 510 MPa and a minimum yield strength of 245 MPa. The higher strength of SS490 allows smaller section sizes for the same design load, reducing the self-weight of structures and the total material cost. The grade is classified as a structural steel rather than a low-carbon mild steel, and its mechanical properties are verified by tensile testing in accordance with JIS G3101.

H-Beam Section Characteristics

The H-beam is a wide-flange section whose cross-section resembles the letter H, with two parallel flanges and a perpendicular web. This geometry gives the section strong bending resistance in all directions and good stability under compressive loads, making it efficient for columns, beams, and trusses. The wide flange provides a large bearing surface for connections, and the section can be supplied in a wide range of heights, widths, web thicknesses, and flange thicknesses to match the design requirements. H-beams are usually delivered in the hot-rolled condition and can be cut, drilled, welded, and connected with bolts at the fabrication stage.

Fabrication and Processing

SS490 H-beam offers good weldability and can be joined by common arc welding processes, including shielded metal arc welding and gas shielded welding, with procedures appropriate for the section thickness. The material can be cut by flame, plasma, or saw cutting, and holes for bolted connections are readily drilled. Because of the moderate carbon content of the grade, no special heat treatment is normally required before or after fabrication, although preheat may be considered for thick sections or highly restrained joints. The material is generally supplied with a mill certificate recording the chemical analysis and mechanical test results in accordance with JIS G3101.

Applications

SS490 H-beam is suitable for building structures with high strength requirements, including multi-storey buildings, industrial plants, and warehouses where columns and beams must carry large loads. It is also used in bridges and other civil engineering structures, in machinery frames and equipment supports, and in temporary works such as shoring and gantries. The section is frequently specified in projects where the design follows the JIS standard system, and it can also serve in projects that accept equivalent grades after engineering review. For offshore or low-temperature applications, additional toughness requirements should be specified and verified with the supplier.

Frequently Asked Questions

What does SS490 mean?

SS490 is a grade in JIS G3101 for rolled steels for general structure. SS identifies structural steel and 490 refers to the minimum tensile strength of 490 MPa, with a minimum yield strength of 285 MPa.

What is the difference between SS400 and SS490?

SS400 has a minimum tensile strength of 400 to 510 MPa and a minimum yield strength of 245 MPa, while SS490 has a tensile strength of 490 to 610 MPa and a yield strength of at least 285 MPa, offering higher load-carrying capacity.

What standard covers SS490 H-beam?

SS490 H-beam is covered by JIS G3101 for rolled steels for general structure and by the relevant JIS standards for hot-rolled H sections, and the mechanical properties are verified in accordance with JIS G3101.

What is the yield strength of SS490?

The minimum yield strength is 285 MPa and the tensile strength is 490 to 610 MPa, with values confirmed by tensile testing at the mill.

Can SS490 H-beam be welded?

Yes. SS490 has good weldability and can be joined by common arc welding processes with appropriate procedures, without special heat treatment in most applications.

What is SS490 approximately equivalent to?

SS490 is approximately comparable in strength level to S355 under EN 10025 and to ASTM A572 Grade 50, although the chemical limits and testing rules differ, and substitution should be verified for the specific project.

Send Inquiry