SS490 H-Beam: JIS G3101 Carbon Steel Sections
SS490 H-beam carbon steel is a hot-rolled structural section made to JIS G3101, the Japanese standard for rolled steel for general structure. In the designation, SS marks the general structural series and 490 indicates the minimum tensile strength of 490 N/mm2. The material is chosen where a straightforward carbon steel section is required to carry predictable loads at moderate cost.
Because the section is rolled with parallel flanges and a deep web, an H-beam resists bending about its strong axis far more efficiently than a flat plate of the same weight. This geometry, combined with the strength level of the grade, makes the profile a default choice for columns, floor beams and bracing in industrial and commercial buildings.
Mechanical Properties Required by JIS G3101
| Property | Requirement |
|---|---|
| Standard | JIS G3101 |
| Yield strength, thickness ≤16 mm | ≥285 MPa |
| Yield strength, thickness >16 mm | ≥275 MPa |
| Tensile strength | 490–610 MPa |
The stepped yield requirement is important in practice. A beam with a thick flange, or a heavy section used as a column, is designed against the lower value, so the section size that works in thin material may still need to be increased for a thick section under the same load.
Why the Yield Strength Limit Matters in Design
Yielding at 285 MPa or more under static load keeps the section within the elastic range for ordinary service conditions.
A high yield-to-tensile ratio is avoided by the minimum tensile requirement, so the beam retains reserve strength before fracture.
The section holds its shape and performance under sustained load and resists plastic deformation, which supports simple elastic design methods.
Uniform property guarantees across the flange and web allow the same grade to be used for beams, columns and bracing in one frame.
Sections, Fabrication and Protection
SS490 is rolled in a full range of H-beam sizes, giving designers a continuous choice of depth, flange width, web thickness and flange thickness.
The material drills, punches, saws and flame cuts with conventional shop equipment and is readily welded with common consumables.
Bolted connections with high-strength friction grip fasteners are standard for site assembly, keeping field welding to a minimum.
Unprotected carbon steel needs a coating system. Shot blasting followed by a primer, or hot dip galvanizing for exposed and humid locations, is the usual route.
Typical Applications of SS490 H-Beams
Main and secondary beams in industrial buildings, warehouses and workshops.
Columns, portal frames and crane runway supports in factory construction.
Floor framing, mezzanine structures and steel platforms.
Bracing, truss chords and temporary works such as supports and staging.
General infrastructure and machinery support structures that do not require special toughness grades.
Selection Notes
SS490 is a general structural grade rather than a building-frame grade with guaranteed impact toughness, so projects in seismic regions or cold climates often specify a different series. When ordering, state the section size, length, tolerance class and surface condition, and confirm whether the design uses the thin or thick yield value. Careful specification at that stage avoids costly substitution later in fabrication.
FAQ
Q: What does SS490 stand for?
SS is the general structural steel series in JIS G3101, and 490 is the minimum tensile strength in N/mm2. It is a plain carbon structural grade intended for general load-carrying members.
Q: What is the yield strength of an SS490 H-beam?
At least 285 MPa for material up to 16 mm thick and at least 275 MPa for thicker material. The thicker value governs the design of heavy sections and thick flanges.
Q: Is SS490 suitable for welded structures?
Yes. The grade is welded daily with common arc processes using matching consumables. Thicker sections and high restraint joints should still be supported by a qualified welding procedure and suitable preheat.
Q: Does SS490 H-beam resist corrosion by itself?
No. It is an ordinary carbon steel and will rust in humid or industrial atmospheres. A paint system, hot dip galvanizing or another protective coating is required for long service life.
Q: Can SS490 be used for columns as well as beams?
Yes. The same rolled sections are used for columns, beams and bracing. For column use the design is governed by buckling and by the yield value applicable to the actual material thickness.
Q: How should an SS490 H-beam be ordered?
Specify the standard, grade, section designation, length, tolerance class and surface treatment. Adding the thickness class and the intended coating helps the mill and the fabricator deliver material that fits the design assumptions without substitution.

