Knowledge

Is A662 Grade C Steel Weldable?

Jan 21, 2026 Leave a message

ASTM A662 Grade C is a carbon-manganese-silicon steel plate used for welded pressure vessels, boilers, and storage tanks, particularly where moderate to lower temperatures are involved and improved low-temperature toughness is needed. The answer to the question in the title is yes: A662 Grade C is weldable, and in fact it is specifically designed for fusion-welded pressure-containing equipment. Its controlled carbon content and balanced chemistry make it suitable for welding with common processes when qualified procedures are followed.

What Is A662 Grade C?

A662 is the ASTM specification covering carbon-manganese-silicon steel plates for intermediate and lower temperature service in welded pressure vessels. The specification offers Grades A, B, and C, with Grade C having the highest manganese content for enhanced strength and toughness. Compared with Grades A and B, Grade C provides a higher yield strength and better low-temperature impact properties, making it suitable for vessels that operate under pressure at moderately low temperatures. Plates are typically supplied in the normalized condition for thicknesses over 40 mm to refine the grain structure and guarantee toughness.

Chemical Composition

The composition of A662 Grade C is a carbon-manganese-silicon system with limits chosen for weldability and low-temperature toughness. The maximum carbon content is 0.24%, and the manganese content is higher than in Grades A and B, in the range of about 0.92-1.72%, which provides the additional strength and hardenability of the grade. Silicon is 0.13-0.45%, and phosphorus and sulfur are each limited to 0.035% maximum. The controlled carbon and impurity levels keep the steel readily weldable while supporting the required mechanical properties.

Mechanical Properties

A662 Grade C has a minimum yield strength of 295 MPa and a tensile strength range of about 485-620 MPa, with a minimum elongation of about 20% in a 2-inch (50 mm) gauge length. The specification requires Charpy V-notch impact testing at a selected test temperature, commonly chosen from -20, -40, or -60 degrees Celsius, to verify low-temperature toughness. The density is approximately 7.85 g/cm3, the modulus of elasticity about 200 GPa, and the melting range about 1420-1460 degrees Celsius, all consistent with carbon-manganese steels.

Weldability of A662 Grade C

A662 Grade C is designed to be welded, and it can be joined by common processes such as SMAW, GMAW, GTAW, and SAW using low-hydrogen consumables and qualified welding procedure specifications. Because the carbon content is controlled, preheating is generally modest, but it is advisable for thick sections or in cold environments, with the exact preheat and interpass temperatures defined by the qualified procedure and the governing construction code. Post-weld heat treatment may be required for thicker vessels or specific service conditions to relieve residual stresses and restore toughness, as determined by the applicable code. After welding, the low-temperature impact properties of the heat-affected zone should be verified where the design relies on them.

Applications

In the petrochemical industry, A662 Grade C is used for medium and low-temperature pressure vessels such as reactors, heat exchangers, separators, spherical storage tanks, and oil, gas, and liquefied petroleum gas storage tanks, operating at temperatures down to about -30 degrees Celsius and above. In the power and energy industry, it is used for boiler drums and pressure-containing components that withstand alternating temperature conditions. In the low-temperature storage and transportation field, it is used for containers for media such as liquid ammonia, liquid nitrogen, and liquefied petroleum gas, suitable for working scenarios from about -20 to -45 degrees Celsius. In water conservancy and hydropower, it is applied to high-pressure water pipes and water turbine volutes.

Frequently Asked Questions

Is A662 Grade C weldable? Yes. A662 Grade C is specifically designed for welded pressure vessels and has good weldability with common processes such as SMAW, GMAW, GTAW, and SAW, using low-hydrogen consumables and qualified procedures.

Can A662 Grade C be used for pressure vessels? Yes. It is specifically designed for pressure vessel applications and meets the strength and toughness requirements of vessels, especially those operating at low temperatures.

What is the yield strength of A662 Grade C? The minimum yield strength is 295 MPa, and the tensile strength range is about 485-620 MPa, with a minimum elongation of about 20% in a 2-inch gauge length.

What is the density of A662 Grade C? The density is approximately 7.85 g/cm3, the same as most carbon and low-alloy steels, which is a key parameter for weight calculation in engineering design.

What corrosion resistance does A662 Grade C have? It has general corrosion resistance in atmospheric and mild chemical environments. For harsh corrosive conditions, additional anti-corrosion treatments such as painting or galvanizing are required.

Can A662 Grade C be cold-formed? Yes, it can be cold-formed under appropriate conditions. Excessive cold working may reduce toughness, so post-forming heat treatment may be needed for critical components.

Send Inquiry