Knowledge

How the Chemical Composition of S690Q Controls Strength, Toughness and Weldability

Dec 30, 2025 Leave a message

The Design Philosophy Behind S690Q Chemistry

The chemical composition of S690Q is not an arbitrary list of elements. It is an engineered recipe that has to satisfy three competing demands at once: hardenability, which delivers the 690 MPa minimum yield strength; toughness, which keeps the material usable at low service temperature; and weldability, which decides whether a fabricator can build the structure at all. Every element pushes at least one of those three levers, and several push in opposing directions.

S690Q is a quenched and tempered structural steel covered by EN 10025-6. Unlike lower grades, where strength comes mainly from carbon, this steel reaches its strength through a low-carbon, micro-alloyed composition combined with a quench and temper treatment that produces a tempered martensitic or bainitic microstructure. The nominal mechanical targets are a minimum yield strength of 690 MPa, a tensile strength of roughly 770 to 940 MPa, a minimum elongation of about 14 %, and 30 J minimum Charpy V-notch energy at the grade's specified test temperature.

Carbon and Manganese: Strength Against Weldability

Carbon is still the primary hardening element. It strengthens the matrix by interstitial solid solution and, more importantly, it is what makes martensite possible at all. The problem is that carbon also raises the ductile-to-brittle transition temperature and promotes cold cracking in the heat-affected zone, which is why the grade keeps carbon at a low ceiling rather than using it as the main alloying tool. The strength that carbon would normally provide is instead obtained from the quench and temper route plus the hardenability elements.

Manganese is the workhorse of hardenability. It increases the depth and uniformity of hardening during quenching so that thick plates transform through the full section rather than only near the surface. It also contributes solid solution strengthening, refines the grain structure and assists deoxidation during steelmaking. Its level is deliberately optimised, because excess manganese increases segregation and raises the carbon equivalent, which harms weldability.

Element Typical maximum in the grade specification Main effect
Carbon (C) 0.20 % Hardenability and martensite formation; limited to protect toughness and weldability
Silicon (Si) 0.80 % Deoxidation and moderate solid solution strengthening
Manganese (Mn) 1.70 % Through-thickness hardenability, grain refinement, deoxidation
Phosphorus (P) 0.025 % Embrittling element, tightly restricted
Sulfur (S) 0.015 % Forms inclusions; restricted for through-thickness ductility
Boron (B) 0.005 % Trace addition with a strong effect on hardenability
Chromium (Cr) 1.50 % Hardenability, tempering resistance, some atmospheric corrosion resistance
Nickel (Ni) 2.00 % Toughness enhancement, especially at low temperature
Molybdenum (Mo) 0.70 % Hardenability, resistance to temper embrittlement, hot strength
Niobium (Nb), Vanadium (V), Titanium (Ti) 0.06 % / 0.12 % / 0.05 % Precipitation strengthening and grain boundary pinning
Carbon equivalent (CEV) 0.65 % Controls preheat and hydrogen management during welding

The maxima above apply to the usual plate thickness range for this grade. Because the standard's limits tighten as thickness increases, the actual delivered composition is normally checked against the certificate rather than assumed.

Micro-Alloying with Niobium, Vanadium, Titanium and Boron

Niobium, vanadium and titanium are added in small, precisely controlled amounts, and they work in two ways. First, they form stable carbonitride precipitates such as NbC, V(C,N) and TiN, which pin grain boundaries during hot rolling and prevent excessive austenite grain growth. Grain refinement is the only mechanism that raises strength and toughness simultaneously, which is why it is so valuable in a grade of this strength class. Second, the fine precipitates impede dislocation movement and add precipitation strengthening without the toughness penalty that carbon would bring.

The same elements need care in the heat-affected zone. Niobium in particular can raise hardness and reduce toughness in that region if the welding heat input and cooling rate are not matched to the composition. Boron is added at trace level, often between 0.0005 % and 0.003 %, and it segregates to grain boundaries where it delays the formation of soft ferrite during quenching. That single trace addition buys so much hardenability that carbon and the other alloying elements can be kept lean, which is exactly what makes a 690 MPa steel weldable in practice.

Chromium, Nickel and Molybdenum: Toughness and Subgrade Choice

Chromium increases hardenability and tempering resistance, so the plate holds its strength after the tempering treatment and retains more of it at elevated service temperature. It also provides a degree of atmospheric corrosion resistance at these levels. Nickel is the premier toughness element: it lowers the ductile-to-brittle transition temperature, improves impact behaviour in the cold and strengthens the matrix without destroying ductility. It is the reason the low-temperature subgrades exist at all.

Molybdenum is a strong hardenability agent, it reduces the risk of temper embrittlement after tempering in a critical temperature band, and it raises high-temperature strength. The subgrade the design calls for therefore directly changes the chemistry: the Q condition is tested at -20 °C, the QL condition at -40 °C and the QL1 condition at -60 °C, and meeting the colder requirements generally means more nickel and tighter control of everything that embrittles. Improved through-thickness grades add a further requirement on sulfur and inclusion shape rather than on strength or toughness.

Impurity Control and the Resulting Property Balance

Impurities do disproportionate damage in a steel at this strength level. Phosphorus increases the ductile-to-brittle transition temperature and encourages intergranular fracture. Sulfur forms manganese sulfide inclusions that elongate into stringers during rolling, and those stringers act as stress concentrators and initiation sites for lamellar tearing in thick plates loaded through the thickness. Both elements are therefore held very low, and calcium treatment is commonly used to convert the remaining inclusions into less harmful globular shapes. Where through-thickness ductility is critical, sulfur is restricted further and the plate is ordered to a Z-quality designation.

Strength above 690 MPa comes from low carbon plus manganese, boron, chromium and molybdenum hardenability, with precipitation strengthening from niobium, vanadium and titanium.

Toughness comes from low carbon, low phosphorus and sulfur, nickel additions and a fine prior austenite grain size produced by micro-alloy precipitates.

Weldability comes from the low carbon and controlled manganese that keep the carbon equivalent, and therefore the heat-affected zone hardness, within manageable limits.

Through-thickness performance comes from very low sulfur and inclusion shape control, not from strength adjustments.

The practical consequence is that specifying S690Q is not simply choosing a strength level. It is choosing a composition profile engineered to deliver that strength together with the toughness, weldability and through-thickness behaviour the application needs, which is why subgrade and quality designation belong in the specification alongside the grade itself.

Frequently Asked Questions

Q: Why is carbon kept so low in S690Q?
Because carbon is the fastest way to lose toughness and weldability. Low carbon suppresses cold cracking in the heat-affected zone, and the strength is recovered through quenching and tempering plus hardenability elements instead.

Q: What does boron actually do in this steel?
A trace addition of boron delays ferrite formation at the grain boundaries during quenching, which raises hardenability dramatically. That allows a leaner, more weldable chemistry to reach the same through-thickness strength.

Q: How does the carbon equivalent affect fabrication?
The carbon equivalent drives preheat and interpass temperature selection and hydrogen control. A higher value means more careful thermal management to avoid cold cracking, which is why the grade limits it and why welding procedures are qualified to EN ISO 15614-1.

Q: Which elements distinguish the low-temperature subgrades?
Nickel is the main lever, supported by very low phosphorus and sulfur and a fine grain size. The Q, QL and QL1 conditions differ mainly in the temperature at which the impact energy is verified.

Q: Why is sulfur control so important for thick plates?
Sulfur forms elongated inclusions that concentrate stress through the plate thickness and can trigger lamellar tearing in welded T-joints. Low sulfur plus inclusion shape control is the standard remedy.

Q: Can a certificate alone confirm the properties?
No. The certificate confirms the composition and the test results for that heat, but the properties still depend on the actual quench and temper practice and on the welding procedure used during fabrication.

Send Inquiry