Knowledge

HEB 200 S355JR Wide Flange H Beam: Specifications

May 13, 2025 Leave a message

HEB200x200x9x15 is a wide flange H beam in the S355JR grade, produced to the European standard EN 10025-2 for hot-rolled products of non-alloy structural steels. The H-section design provides strong bending resistance in all directions, making the beam suitable for columns, beams, and load-bearing frames in buildings and industrial structures. This article describes the dimensions, material properties, and processing characteristics of the section.

Dimensions and Section Properties

In the designation HEB200x200x9x15, the height and width of the steel section are both 200 mm, the web thickness is 9 mm, and the flange thickness is 15 mm. The cross-sectional area is 47.1 square centimeters, and the theoretical weight is about 37 kg per meter. The wide and thick flange combined with a reasonable web thickness provides good stability and load-bearing capacity, effectively dispersing stress and allowing the section to withstand large loads in structural applications.

Material Standard and Grade

The beam is implemented to the EN 10025-2:2004 European standard, which applies to hot-rolled products of non-alloy structural steels. The S355JR grade designation identifies a structural steel with a minimum yield strength of 355 MPa and a Charpy V-notch impact requirement of 27 J at 20 C in the longitudinal direction. S355JR is one of the most widely used structural grades in Europe and is commonly adopted for building frames, bridges, and machinery structures where a combination of strength and weldability is required.

Chemical Composition

The heat analysis of the S355JR section is limited to carbon 0.22% maximum, silicon 0.55% maximum, manganese 1.60% maximum, phosphorus 0.025% maximum, and sulfur 0.025% maximum. The low carbon content supports welding without excessive hardening, while the manganese provides solid-solution strengthening. The controlled phosphorus and sulfur limits contribute to toughness and formability, and the material can be supplied with mill certificates recording the chemical analysis and mechanical test results in accordance with EN 10204.

Mechanical Properties

When the thickness is 16 mm or less, the yield strength is at least 355 MPa; as the thickness increases, the yield strength decreases gradually, for example to at least 345 MPa for thicknesses from 16 to 40 mm. The tensile strength is between 470 and 630 MPa, the minimum elongation A5 is 22% for thicknesses from 3 to 40 mm, and the longitudinal impact energy is not less than 27 J at 20 C. These values follow the thickness-dependent requirements of EN 10025-2 and ensure reliable performance in both static and dynamic load-bearing structures.

Processing and Delivery

The section has good plasticity, which makes it convenient for cutting, welding, and cold bending forming, and it can adapt to various welding processes such as arc welding and gas shielded welding. The beam is usually delivered in the hot-rolled state, meaning the steel is supplied directly after hot rolling without additional heat treatment, which reduces cost and meets the use requirements of most projects. For projects requiring higher toughness at low temperature, the S355J2 grade with a -20 C impact requirement, or normalized grades, should be considered.

Frequently Asked Questions

What does HEB200x200x9x15 mean?

The designation describes a wide flange H beam with a height and width of 200 mm, a web thickness of 9 mm, and a flange thickness of 15 mm.

What is the theoretical weight of HEB200?

The theoretical weight is about 37 kg per meter, based on a cross-sectional area of 47.1 square centimeters.

What standard is HEB200x200x9x15 produced to?

The section is produced to the EN 10025-2:2004 European standard for hot-rolled products of non-alloy structural steels, in the S355JR grade.

What is the yield strength of S355JR HEB200?

The minimum yield strength is 355 MPa for thicknesses up to 16 mm and 345 MPa for thicknesses from 16 to 40 mm, with a tensile strength of 470 to 630 MPa.

What is the impact requirement for S355JR?

The longitudinal impact energy is not less than 27 J at 20 C, in accordance with EN 10025-2 for the JR impact designation.

Is the HEB200 section weldable?

Yes. The section has good plasticity and can be joined by arc welding and gas shielded welding, and can be cut and cold bent to shape without difficulty.

Send Inquiry