P295GH is a boiler quality steel plate made to EN 10028-2, the European standard for flat products of pressure equipment. It is a non-alloy fine grain steel supplied in the normalized delivery condition, which means the plate is heated above the transformation range and cooled in air so that the grain structure is uniform and the mechanical properties are consistent through the thickness. P295GH is a standard selection for pressure vessel shells, boiler pressure parts and pipework that carries hot, high pressure media.
What P295GH Boiler Quality Steel Plate Is
The designation follows the EN pressure vessel system. The letter P marks a pressure purposes steel, the number 295 is the minimum yield strength in MPa for the thinnest plates, and the letters G and H identify a steel intended for service at elevated temperature and supplied to a fine grain specification. Because the grade is non-alloy, it relies on grain refinement and normalizing rather than on alloy additions for its properties, which keeps it economical and easy to weld.
Standard: EN 10028-2
Type: non-alloy fine grain steel for pressure purposes
Delivery condition: normalized
Yield strength range: 220-295 MPa depending on thickness
Tensile strength range: 430-580 MPa depending on thickness
Impact energy: 27 J at -20 °C, 34 J at 0 °C and 40 J at +20 °C
Chemical Composition of P295GH Steel Plate
The analysis is deliberately restricted so that toughness and weldability are preserved in thick sections. Carbon is capped low, residuals such as sulphur and phosphorus are tightly limited, and aluminium is added to pin the grain size during normalizing.
| Element | Requirement (%) | Element | Requirement (%) |
|---|---|---|---|
| C | 0.08-0.20 | Cr | max 0.30 |
| Si | max 0.40 | Cu | max 0.30 |
| Mn | 0.90-1.50 | Mo | max 0.08 |
| P | max 0.025 | Nb | max 0.020 |
| S | max 0.015 | Ni | max 0.30 |
| Al | min 0.020 | Ti | max 0.03 |
| N | max 0.012 | V | max 0.02 |
Aluminium is the grain refining element in this grade, so it is specified as a minimum rather than as a maximum; a content above 0.020% total ensures that fine austenitic grain size is retained after normalizing. The carbon and manganese range sets the strength level, while the very low sulphur limit protects toughness in the through thickness direction. Niobium and vanadium are allowed only in small amounts because a higher level would promote precipitation in the heat affected zone and reduce toughness after welding.
Mechanical Properties of EN 10028-2 P295GH
Properties are guaranteed in the normalized condition and are graded by plate thickness, since heavier plate cools more slowly and cannot reach the same strength as thin plate.
| Thickness (mm) | Yield strength min (MPa) | Tensile strength (MPa) | Elongation min (%) |
|---|---|---|---|
| ≤16 | 295 | 460-580 | 21 |
| >16 to ≤40 | 290 | 460-580 | 21 |
| >40 to ≤60 | 285 | 460-580 | 21 |
| >60 to ≤100 | 260 | 460-580 | 21 |
| >100 to ≤150 | 235 | 440-570 | 21 |
| >150 to ≤250 | 220 | 430-570 | 21 |
Charpy impact testing is carried out on normalized material at three temperatures. The minimum absorbed energy is 27 J at -20 °C, 34 J at 0 °C and 40 J at +20 °C, which confirms usable toughness both in cold start up conditions and in warm service. The guaranteed minimum elongation of 21% leaves enough ductility for forming, rolling and dished head production.
Normalizing and Heat Treatment
Normalizing is the reason this grade behaves predictably in pressure service. After rolling, the plate is reheated to roughly 900-950 °C, held long enough for the structure to become fully austenitic, and then cooled in still air. The result is a fine, even ferrite and pearlite structure with no banding from segregation, and with toughness that does not depend heavily on the plate position. If fabrication requires further hot forming, the component can be re-normalized to restore the specified properties, and post weld heat treatment at conventional stress relief temperatures is compatible with the grade.
Applications of P295GH Boiler Plate
Pressure vessels. Storage tanks, reactors and separators use P295GH reactor plate because the grade combines a guaranteed yield strength with good toughness and weldability in wall thicknesses up to 250 mm.
Boilers. Pressure parts of industrial and power station boilers, including drums and headers, are a classic application of P295GH boiler plate.
Pipelines. P295GH pressure vessel steel serves pipework that transports high temperature and high pressure media, where strength at the design temperature must be maintained for the whole service life.
Chemical equipment. Structural parts of chemical plant equipment also use P295GH boiler steel plate, particularly where a normalized fine grain steel with verified impact energy is required.
Frequently Asked Questions
Q: What standard covers P295GH steel plate?
EN 10028-2, the specification for flat products of non-alloy and alloy steels for pressure purposes, with P295GH listed among the non-alloy fine grain grades.
Q: What is the yield strength of P295GH?
295 MPa minimum for plate up to 16 mm, decreasing in steps to 290, 285, 260 and 235 MPa as thickness increases, and reaching 220 MPa for plate between 150 mm and 250 mm.
Q: Is P295GH supplied normalized?
Yes. The G and H symbols in the grade call for a fine grain, normalized delivery condition, and the specified mechanical properties apply to material tested in that condition.
Q: What impact energy does P295GH guarantee?
A minimum of 27 J at -20 °C, 34 J at 0 °C and 40 J at +20 °C on Charpy V notch specimens.
Q: Why is aluminium limited in this plate?
Aluminium is added on purpose for grain refinement, so it is specified as a minimum of 0.020% rather than as a maximum; the small amount of dissolved aluminium keeps the grain size fine after normalizing.
Q: Can P295GH be welded and stress relieved?
Yes. The low carbon content and the tight sulphur and phosphorus limits make the grade suitable for welded pressure equipment, and post weld heat treatment can be applied to relieve residual stress.

