Knowledge

W27x114 Wide Flange Beam in ASTM A572 Grade 50 Carbon Steel

May 26, 2025 Leave a message

W27x114 Wide Flange Beam: Section and Steel Grade Overview

A W27x114 is a hot-rolled wide flange (W-shape) beam made in ASTM A572/A572M Grade 50 carbon steel. The designation follows the naming convention used for structural shapes: the first figure is the nominal depth in inches and the second is the nominal mass in pounds per foot, so a W27x114 measures 27 in (about 693 mm) deep and weighs 114 lb/ft (approximately 170 kg/m).

Wide flange sections place most of their material in two parallel flanges, which gives a high strong-axis moment of inertia for a given weight. Combined with the 345 MPa minimum yield strength of A572 Grade 50, this makes the W27x114 a practical choice for heavily loaded beams, transfer girders, columns and crane runway structures.

Nominal Section Dimensions

Parameter Metric Imperial
Overall depth (h) 693 mm 27.3 in
Flange width (b) 256 mm 10.1 in
Flange thickness (tf) 14.5 mm 0.57 in
Web thickness (tw) 23.6 mm 0.93 in
Nominal mass about 170 kg/m 114 lb/ft

Depth, flange width, flange and web thickness, out-of-square and straightness are controlled by ASTM A6/A6M, the general requirements standard for rolled structural shapes. When ordering, state the grade, the required length, the number of pieces and whether the beam is required in mill lengths or cut to a drawing dimension.

ASTM A572 Grade 50 Material Properties

ASTM A572/A572M covers high-strength low-alloy structural steel in Grades 42, 50, 55, 60 and 65. Grade 50 is the most widely specified of these for rolled shapes and plates because it delivers a useful strength increase over ordinary carbon structural steel while remaining suitable for routine fabrication.

Minimum yield strength: 345 MPa (50 ksi)

Minimum tensile strength: 450 MPa (65 ksi)

Typical chemistry limits: carbon 0.23% max, manganese 1.35% max, phosphorus 0.04% max, sulphur 0.05% max, silicon 0.40% max

Micro-alloying with niobium or vanadium to reach the strength level without an excessive carbon content

Good toughness and ductility for welded and bolted structural work

A572 Grade 50 is not a weathering steel. Where atmospheric corrosion resistance is needed, a copper-bearing weathering grade is specified instead and the member is normally left unpainted so that a stable protective oxide layer can form.

Weldability, Fabrication and Corrosion Protection

The low-alloy composition of A572 Grade 50 keeps the carbon equivalent moderate, so the beam welds readily with the processes used in structural shops, including shielded metal arc, gas metal arc and flux-cored arc welding. Two practices matter most on thicker sections:

Use low-hydrogen electrodes and consumables matched to the base metal strength.

Preheat to roughly 100-150 °C to drive off moisture and avoid hydrogen-induced cold cracking, particularly where the web-to-flange region or thick flanges create high restraint.

Flame cutting and plasma cutting are both acceptable for a W27x114, provided the cut edges are cleaned of dross and heavy oxide before welding. Holes for connections are normally drilled or punched and reamed where required; high-strength structural bolts to ASTM F3125/F3125M are commonly used for field connections, while shop connections are frequently welded.

In service, because A572 Grade 50 is a lean low-alloy steel rather than a stainless or weathering grade, it behaves like ordinary structural carbon steel in aggressive environments. The essential protective measures are:

Shop-applied paint or coating systems for indoor and sheltered outdoor service

Hot-dip galvanizing where long-term atmospheric exposure or occasional wetting is expected

Drainage detailing that prevents water from standing on the top flange or in pockets

Periodic inspection of coated surfaces in humid, coastal or chemically loaded atmospheres

For building frames in the United States, ASTM A992/A992M is the customary shape specification and its strength level matches A572 Grade 50, so the two are frequently compared in the same project discussion. For bridgework, ASTM A709 covers comparable strength levels and adds toughness requirements for fracture-critical members.

Typical Applications

High-rise building frames and column sections

Industrial plant support beams and equipment skids

Long-span roof and floor girders

Crane runway beams and monorail supports

Heavy machinery bases, port handling structures and mining equipment frames

Bridge girders and pier cap beams where the applicable bridge standard permits

FAQ

Q: What does the designation W27x114 mean?
It is a wide flange shape with a nominal depth of 27 inches and a nominal mass of 114 pounds per foot, equivalent to an actual depth of about 693 mm and a mass of about 170 kg/m.

Q: What are the mechanical properties of ASTM A572 Grade 50?
The standard requires a minimum yield strength of 345 MPa (50 ksi) and a minimum tensile strength of 450 MPa (65 ksi), with a chemistry controlled for low-alloy, weldable structural performance.

Q: Is a W27x114 the same as a metric H-beam?
Both are wide flange profiles. The W range is dimensioned in inches to ASTM A6, while metric H-beams follow European or Asian series, so the two families are close in concept but not interchangeable dimension by dimension.

Q: Can A572 Grade 50 beam be welded without preheat?
Thin, lightly restrained joints can often be welded without preheat, but a preheat of about 100-150 °C is recommended for thicker sections and high-restraint connections to prevent cold cracking.

Q: How should the beam be protected against corrosion?
Paint systems and hot-dip galvanizing are the standard options. Detailing that sheds water is equally important, because A572 Grade 50 has no inherent weathering resistance.

Q: Can the beam be supplied in cut lengths?
Yes. Rolled wide flange beams are supplied in mill lengths or cut to a specified drawing dimension, with the cut ends squared and identified for the project.

Send Inquiry