Knowledge

Why choose SA387 Grade 12 Class 2 over other grades?

Jan 09, 2026 Leave a message

Why choose SA387 Grade 12 Class 2 over other grades?

 

info-304-310

 

SA387 Grade 12 Class 2 (also designated as A387 Gr 12 Cl 2) is a high-quality chrome-molybdenum alloy steel plate primarily used for weldable pressure vessels and industrial boilers designed for elevated temperature service.

Choosing SA387 Grade 12 Class 2 over other grades is a balanced engineering and economic decision, driven by its specific combination of properties, cost, and fabrication advantages.

 

1. Compared to Lower Grades (e.g., Carbon Steels like SA516)

Superior Elevated-Temperature Performance: Grade 12 Class 2 offers significantly better creep strength and allowable stress values at temperatures above ~370°C (~700°F). It is designed for sustained service where carbon steel would weaken or creep excessively.

Improved Oxidation Resistance: The 1% chromium content provides better resistance to scaling and oxidation in hot steam or flue gas environments compared to plain carbon steel.

2. Compared to Lower-Alloy Cr-Mo Grades (e.g., SA387 Grade 11)

Cost-Effectiveness: Grade 12 (1Cr-0.5Mo) typically has a lower alloy cost than Grade 11 (1.25Cr-0.5Mo) due to slightly lower chromium content, while still offering comparable performance in many moderate-temperature applications.

Adequate for Moderate Conditions: For many boiler drums, heat exchangers, and pressure vessels operating in the ~425–540°C (~800–1000°F) range, Grade 12 Class 2 provides sufficient strength and corrosion resistance, making it an economical choice.

3. Compared to Higher-Alloy Cr-Mo Grades (e.g., SA387 Grade 22, Grade 5)

Lower Cost: It is significantly less expensive than grades with higher chromium and molybdenum content (e.g., Grade 22 with 2.25Cr-1Mo or Grade 5 with 5Cr-0.5Mo), making it ideal for applications where extreme high-temperature strength or corrosion resistance is unnecessary.

Easier Fabrication & Welding: Lower alloy content generally simplifies welding procedures, reduces preheat/post-heat requirements, and lowers the risk of hydrogen cracking compared to higher-alloy steels.

4. Compared to SA387 Grade 12 Class 1 (Annealed Condition)

Higher As-Supplied Strength: Class 2 is normalized and tempered (N+T), providing higher yield and tensile strength in the as-delivered state (min. yield strength ~275 MPa/40 ksi vs. ~205 MPa/30 ksi for Class 1). This allows for thinner vessel designs or higher design pressures.

Reduced Fabrication Complexity: For components requiring minimal severe cold forming, Class 2 can be used as-supplied, potentially eliminating the need for a full post-fabrication normalizing and tempering heat treatment (though PWHT for stress relief is still required after welding).

5. Key Advantages Summary:

Balanced Performance: Optimal for moderate elevated-temperature service where carbon steel is inadequate but high-alloy steel is overkill.

Proven Reliability: Widely used in power boilers, heat exchangers, and refinery vessels with a long service history under ASME codes.

Favorable Cost-to-Performance Ratio: Offers better high-temperature properties than carbon steel without the premium cost of higher-alloy Cr-Mo steels.

Ready-to-Use Strength: The N+T condition (Class 2) provides immediate mechanical properties suitable for many designs without additional heat treatment before fabrication.

 

Equivalent Grades For SA387 Alloy Steel Gr.12 CL 2 Sheets & Plates

BS EN ASTM/ASME UNS DIN
– – A387 / SA 387 K11757 –

 

Chemical Composition of SA387 Alloy Steel Gr.12 CL 2 Sheets and Plates

C Mn P S Si Cr Mo
0.04 – 0.17 0.35 – 0.73 0.035 0.035 0.13 – 0.45 0.74 – 1.21 0.4 – 0.65

 

 

When to Choose SA387 Grade 12 Class 2:

Typical Applications:

Boiler drums and superheater headers (in lower-temperature sections).

Heat exchangers and process vessels in refineries/petrochemical plants operating below ~540°C (~1000°F).

Steam piping and components where cyclic thermal stress is moderate.

Design Conditions: When the ASME Boiler and Pressure Vessel Code allowable stress values for Grade 12 at the design temperature meet the pressure requirements efficiently, and the environment does not require higher chromium resistance.

 

When to Consider Other Grades:

Choose Carbon Steel (e.g., SA516): For temperatures below ~370°C (~700°F) where cost is paramount.

Choose Higher-Alloy (e.g., Grade 22): For temperatures above ~540°C (~1000°F), high hydrogen partial pressure, or superior creep strength.

Choose Grade 12 Class 1: If severe cold forming is required and final PWHT can be fully controlled.

 

In essence

SA387 Grade 12 Class 2 is the pragmatic choice for cost-sensitive, moderate-temperature pressure vessel applications where enhanced performance over carbon steel is needed, but the expense of advanced alloys is not justified. It strikes a balance between performance, fabricability, and total cost

 

 

Contact now

 

 

 

1.What is SA387 Grade 12 Class 2?
SA387 Grade 12 Class 2 is a chromium-molybdenum alloy steel plate designed for welded pressure vessels, supplied in the normalized and tempered heat-treated condition for improved toughness and strength.

2.What is the difference between SA387 Gr12 Cl 1 and Cl 2?
The key difference is the mandatory heat treatment. Grade 12 Class 2 must be supplied normalized and tempered, while Class 1 can be supplied as-rolled, annealed, or normalized and tempered, affecting its mechanical properties.

3.What is the chemical composition of SA387 Grade 12 Class 2?
Its typical composition includes Chromium (0.80-1.25%), Molybdenum (0.44-0.65%), Carbon (max 0.17%), Manganese (0.40-0.65%), Silicon (0.15-0.40%), and limited Phosphorus and Sulfur.

4.What are the mechanical properties of SA387 Gr12 Cl 2?
Key properties include a minimum tensile strength of 485 MPa (70 ksi) and a minimum yield strength of 275 MPa (40 ksi) for thicknesses up to 65mm, with higher strength than Class 1.

5.What is SA387 Gr12 Cl 2 equivalent to?
It is equivalent to ASTM A387 Gr12 Cl 2, ASME SA387 Gr12 Cl 2, and the common material grade UNS K11757. It is similar to 1.25%Cr-0.5%Mo steel.

6.What is the heat treatment for SA387 Grade 12 Class 2?
Per the specification, SA387 Grade 12 Class 2 plates are supplied in the normalized (heated above the critical temperature and air-cooled) and subsequently tempered (reheated to a specific sub-critical temperature) condition.

7.Why choose Class 2 over Class 1 for SA387 Grade 12?
Class 2 is chosen when the application requires guaranteed higher strength, better microstructural uniformity, and improved notch toughness due to its mandatory normalized and tempered condition.

8.What is the maximum operating temperature for SA387 Gr12 Cl 2?
It is commonly used for service temperatures up to approximately 800-850°F (427-454°C), particularly in hydrogen service and other high-temperature refinery applications.

9.How to weld SA387 Grade 12 Class 2 steel?
Welding requires preheating (typically 250-400°F / 121-204°C) and a mandatory post-weld heat treatment (PWHT). Common filler metals include AWS E8018-B2 for SMAW or equivalent.

10.What is the hardness of SA387 Grade 12 Class 2?
Hardness is not directly specified in the standard but is controlled by the heat treatment and mechanical properties. For service in wet H2S environments, it is often specified to be below 200 HB or 22 HRC to resist sulfide stress cracking.

 

Full specification and details are available on request. The above information is provided for guidance purposes only. For specific design requirements please contact our technical sales staff.

info-500-499

 

 

Send Inquiry