A387 Grade 11 Class 2 is a chromium-molybdenum alloy steel plate defined in ASTM A387 and ASME SA387, designed for elevated-temperature service in boilers and pressure vessels. It is chosen for applications where carbon steels lose strength and where resistance to creep, oxidation, and hydrogen attack is required, such as refinery reactors, boiler drums, and high-temperature heat exchangers.
Why This Grade Is Specified
Elevated-temperature strength: the steel retains useful mechanical properties up to about 593 deg C (1100 deg F), which carbon steel cannot provide.
Creep resistance: molybdenum contributes sustained strength under long-term high-temperature, high-pressure exposure.
Oxidation and corrosion resistance: the chromium content provides better high-temperature oxidation resistance than carbon steel.
Resistance to hydrogen attack: the Cr-Mo chemistry performs well in high-temperature hydrogen service in refinery and petrochemical equipment.
Class 2 strength: the normalized and tempered condition delivers a minimum yield of 310 MPa and a tensile range of 515-690 MPa, reducing required plate thickness compared with Class 1.
Fabricability: with qualified procedures, the grade welds reliably and is routinely fabricated into large vessels followed by post-weld heat treatment.
Composition and Class 2 Properties
The nominal composition of A387 Grade 11 is 1.25% chromium and 0.5% molybdenum. Typical composition limits per ASTM A387/A387M are carbon 0.05-0.17%, manganese 0.40-0.65%, silicon 0.50-1.00%, phosphorus and sulfur 0.035% max, chromium 1.00-1.50%, and molybdenum 0.45-0.65%. Class 2 plates are supplied in the normalized and tempered condition with a minimum yield strength of 310 MPa and a tensile strength of 515-690 MPa; the mill test certificate is the authoritative reference for verification.
Advantages Over Carbon Steel
Compared with carbon steel plates such as A516, A387 Grade 11 Class 2 retains strength at temperatures above about 400 deg C where carbon steel properties fall off sharply, offers superior oxidation resistance, and resists hydrogen-induced damage in high-temperature hydrogen service. This is why it replaces carbon steel in elevated-temperature pressure-containing components rather than for ambient-temperature service, where carbon steel remains more economical.
Applications
Oil and gas industry: refinery and petrochemical equipment, high-temperature piping, and vessels exposed to hydrogen sulfide, high pressure, and cyclic thermal stress.
Power generation: boiler drums, headers, and high-temperature steam piping in thermal and combined-cycle plants.
Chemical processing: vessels and heat exchangers handling hot corrosive liquids and gases in high-temperature reaction service.
Heat exchangers and boilers: heavy-duty thermal transfer equipment across the pharmaceutical, metallurgical, and food processing industries.
Fabrication Considerations
Welding: preheating is required (commonly 150-250 deg C depending on thickness and the qualified procedure), interpass temperature must be controlled, and low-hydrogen Cr-Mo consumables should be used.
Post-weld heat treatment: PWHT is normally performed to relieve residual stress and restore toughness, at a temperature below the original tempering temperature of the base metal.
Forming: hot forming should stay within the recommended temperature range; if the temperature falls below the transformation point, a full heat treatment cycle should be repeated.
Testing: pressure-retaining welds are typically examined by radiographic or ultrasonic testing, with hardness checks and positive material identification where specified.
Frequently Asked Questions
What is A387 Grade 11 Class 2 equivalent to? ASME SA387 Grade 11 Class 2 is the code designation of the same material. The closest European comparable grade is 13CrMo4-5 per EN 10028-2; equivalence must be verified property by property against the design specification.
What is the difference between Class 1 and Class 2? Class 2 is normalized and tempered with a minimum yield of 310 MPa and a tensile range of 515-690 MPa, while Class 1 has a minimum yield of 205 MPa and a tensile range of 415-585 MPa.
What is the maximum service temperature of A387 Grade 11 Class 2? commonly referenced continuous service limit is about 593 deg C (1100 deg F); above this temperature, creep and oxidation resistance decline significantly.
Why is this grade used in hydrogen service? The chromium-molybdenum composition resists the decarburization and fissuring caused by high-temperature hydrogen, which is why it performs reliably in refinery hydrogen service within the limits of the governing design curves.
Can A387 Grade 11 Class 2 be used in sour gas service? The grade is used in refinery and petrochemical environments with hydrogen sulfide, but suitability for specific sour service must be confirmed against hardness limits and the applicable code requirements.
What is A387 Grade 11 Class 2 used for? It is used for pressure vessels, boilers, heat exchangers, and high-temperature piping in the oil, gas, petrochemical, and power industries, where elevated-temperature strength and resistance to hydrogen attack are required.

