Knowledge

How to Source A387 Grade 11 Class 1 Steel Plates

Jan 07, 2026 Leave a message

ASTM A387 Grade 11 Class 1 is a chromium-molybdenum (Cr-Mo) alloy steel plate designed for welded pressure vessels and boilers in elevated-temperature service. The Grade 11 chemistry contains 1.00 to 1.50 percent chromium and 0.45 to 0.65 percent molybdenum, and Class 1 plates are supplied in the annealed or normalized and tempered condition. Because the material is governed by the A387/A387M specification and is usually subject to pressure vessel code requirements, sourcing it involves verifying more than price and dimensions. This article explains where to buy the plate and how to purchase it correctly.

Material Overview and Key Properties

Before purchasing, confirm that the plate meets the specification requirements. For Grade 11 Class 1, the tensile strength is 75 to 100 ksi (515 to 690 MPa), the minimum yield strength is 43 ksi (310 MPa) at 0.2 percent offset, and minimum elongation is 18 percent in 8 inches and 22 percent in 2 inches. The heat analysis ranges are carbon 0.05 to 0.17 percent, manganese 0.40 to 0.65 percent, phosphorus and sulfur 0.035 percent maximum each, silicon 0.50 to 0.80 percent, chromium 1.00 to 1.50 percent, and molybdenum 0.45 to 0.65 percent. The purchaser should also define the required plate dimensions, quantity, delivery condition, and any supplementary requirements such as Charpy impact testing, ultrasonic examination, or simulated post-weld heat treatment testing.

Authorized Supply Channels

A387 Grade 11 Class 1 is available from three main types of suppliers. Steel mills that specialize in pressure vessel plate produce the material to order, which suits large project quantities but involves mill lead times. Stockists and distributors that carry alloy pressure vessel plate can supply smaller quantities from inventory with shorter delivery, typically cutting plates to size on request. Traders and brokers can locate material across different mills, but the buyer must verify that the material test certificate and heat numbers are fully traceable to an accredited producer. For pressure vessel projects, the supplier should be able to demonstrate that the material was produced under the applicable specification and that all required tests were witnessed or certified as agreed.

Documents and Certification to Request

A complete material test report (MTR) is essential. It should show the heat number, chemical analysis, mechanical test results, heat treatment details, and the specification and edition to which the plate was made. For Class 1 plates, confirm the delivery condition stated on the certificate. If supplementary testing is required, request the corresponding reports, such as Charpy impact curves, ultrasonic examination results, hardness readings, or simulated post-weld heat treatment verification. Where the project demands it, arrange third-party inspection at the mill or the stockist's warehouse, and confirm that the inspection agency will issue the required release documents. Keep the mill marking and heat number visible on each plate so that traceability is maintained from receipt to fabrication.

Comparing Quotations Effectively

Price comparisons are only meaningful when quotations are based on the same commercial terms. Confirm whether the price is per tonne or per piece, and whether it is based on theoretical or actual weight. Check what is included: cutting and edge preparation, supplementary testing, packaging, and the cost of certification documents. Confirm the delivery terms, whether ex-works, FOB, CFR, or delivered to site, and whether freight and insurance are included. Ask about the alloy surcharge policy, because chromium and molybdenum prices move with the metal market and some suppliers adjust the price at billing. A lower headline price may hide exclusions, so compare the total delivered cost with all required services included.

Logistics and Acceptance Considerations

Heavy alloy plates are expensive to transport, so the plate dimensions and total weight significantly affect freight cost, whether shipped by container or break-bulk. Plan the order so that plates are cut and delivered in dimensions that suit both the fabricator's handling equipment and the transport mode. On receipt, inspect the plates for damage, verify the heat numbers against the certificates, and check the surface condition and dimensions. If the plates are to be stored before use, follow proper storage practices to prevent corrosion and preserve traceability. Any deviation from the specification should be documented and agreed with the supplier before the material enters production.

Frequently Asked Questions

Where can A387 Grade 11 Class 1 plates be purchased?

From pressure vessel plate mills for large project quantities, from specialist alloy plate stockists for smaller quantities, and from traders who source material across producers, always with full certificate traceability.

What documents should be requested from the supplier?

At minimum the material test report with heat number, chemical analysis, mechanical results, and heat treatment details, plus any supplementary test reports and third-party inspection documents agreed at order.

What is a typical lead time for this grade?

Stock material can be delivered in days to a few weeks, while mill production normally takes several weeks to months depending on the quantity, dimensions, and supplementary requirements.

How is the plate usually priced?

Plate is generally quoted per tonne, with the price depending on grade, thickness, width, quantity, testing, delivery terms, and the prevailing alloy surcharge for chromium and molybdenum.

Can small quantities be purchased?

Yes, small quantities are available from stockists, although the unit price is normally higher than for large mill orders because fixed processing and handling costs are spread over fewer tonnes.

What delivery condition should be specified?

For Class 1, specify the annealed or normalized and tempered condition as required by the design and the subsequent fabrication route, and confirm it on the material test certificate.

Send Inquiry