Knowledge

ASTM A537 Class 3 Steel: Related Standards and Specifications

Jan 13, 2026 Leave a message

ASTM A537 Class 3 is a high-strength, quenched and tempered carbon-manganese-silicon steel plate used primarily for fusion-welded pressure vessels, boilers, and storage tanks in moderate-pressure applications. The quench and temper treatment gives the plate a minimum yield strength of 380 MPa, equal to 55 ksi, for thicknesses up to 65 mm, together with good low-temperature notch toughness. The A537 specification covers three classes: Class 1 in the normalized condition, Class 2 quenched and tempered, and Class 3 quenched and tempered with higher strength and more demanding requirements. This article reviews the standards related to A537 Class 3, including material specification, testing practice, fabrication rules, and application guidance.

What Is ASTM A537 Class 3?

ASTM A537 is the standard specification for pressure vessel plates, carbon steel, heat-treated for improved toughness. It covers three classes: Class 1 in the normalized condition, Class 2 quenched and tempered, and Class 3 quenched and tempered with higher strength and additional requirements. Class 3 is a carbon-manganese-silicon steel that develops its properties through quenching and tempering, which refines the microstructure and improves both strength and low-temperature notch toughness. The grade is primarily used for fusion-welded pressure vessels, boilers, and storage tanks in moderate-pressure applications, with a minimum yield strength of 380 MPa, equal to 55 ksi, for thicknesses up to 65 mm.

Chemical Composition

The maximum carbon content of A537 Class 3 is 0.24 percent. Manganese is specified at 0.70 to 1.35 percent for plates up to 40 mm thick and 1.00 to 1.60 percent for thicker plates, where the higher manganese content improves strength and hardenability. Phosphorus and sulfur are each limited to 0.035 percent maximum to reduce embrittlement and improve toughness. Silicon is 0.15 to 0.50 percent, and copper, nickel, chromium, and molybdenum may be added within small limits when specified. This composition gives the plate the hardenability needed for the quench and temper treatment.

Tensile Requirements by Thickness

The required tensile properties depend on plate thickness. For thicknesses up to 65 mm, the tensile strength is 80 to 100 ksi, about 550 to 690 MPa, with a minimum yield strength of 55 ksi, about 380 MPa. For thicknesses over 65 mm up to 100 mm, tensile strength is 75 to 95 ksi, about 515 to 655 MPa, with a minimum yield of 50 ksi, about 345 MPa. For thicknesses over 100 mm up to 150 mm, tensile strength is 70 to 90 ksi, about 485 to 620 MPa, with a minimum yield of 40 ksi, about 275 MPa. Plates are generally available up to 6 inches, about 150 mm, in thickness.

Heat Treatment and Fabrication

Quenching and tempering are the core of the Class 3 process. Plates are heated to an austenitizing temperature of about 815 to 900 degrees Celsius and rapidly cooled in water or oil, then reheated to a tempering temperature of at least 620 degrees Celsius for a minimum of half an hour per inch of thickness, followed by air cooling. In fabrication, cutting is done by oxy-fuel, plasma, or laser methods with careful heat control to avoid edge cracking. Cold forming is common for rolling shells and pressing heads, and if the material is heated above the tempering temperature during forming, it must be re-quenched and tempered. Welding requires strict preheat and interpass temperature control to prevent hydrogen cracking and heat-affected zone softening, and post-weld heat treatment is often applied below the original tempering temperature.

Related Standards and Testing

The governing document is ASTM A537, which sets the chemistry, heat treatment, and tensile requirements for Class 3. For inspection, plates usually undergo ultrasonic examination in accordance with ASTM A609 or similar standards to detect internal flaws such as laminations, voids, and inclusions. Hardness after heat treatment is typically limited to a maximum of about 235 HB to preserve weldability and toughness. Supplementary requirements may add impact testing at low temperature, and fabrication into pressure vessels follows the applicable ASME Boiler and Pressure Vessel Code rules. Related material standards such as A516 are often compared with A537 when selecting between lower-strength normalized plates and higher-strength quenched and tempered plates.

Frequently Asked Questions

What is the difference between Class 1, Class 2, and Class 3 of A537? Class 1 is supplied in the normalized condition, while Class 2 and Class 3 are quenched and tempered; Class 3 has the highest strength and additional requirements.

What ultrasonic testing standard applies to A537 Class 3? Plates usually undergo ultrasonic inspection in accordance with ASTM A609 or similar standards to detect internal flaws such as laminations and inclusions.

What is the maximum hardness allowed for A537 Class 3? The maximum hardness is typically about 235 HB, which ensures good weldability and toughness after heat treatment.

What welding consumables are suitable for A537 Class 3? Low-hydrogen electrodes such as E7018 for shielded metal arc welding, ER70S-6 for gas metal arc welding, E71T-1 for flux-cored arc welding, and EL8 with matching fluxes for submerged arc welding are commonly used.

Is post-weld heat treatment required for A537 Class 3? PWHT is often recommended, especially for thick sections or highly restrained joints, at typical temperatures of 550 to 620 degrees Celsius to relieve residual stress and improve toughness.

How does A537 Class 3 compare with A516 grades? 537 Class 3 offers higher strength than A516 grades, allowing thinner plates and weight reduction, and provides better low-temperature toughness for demanding pressure vessel and storage tank applications.

Send Inquiry