Knowledge

Hot Rolled vs Cold Rolled Steel: Temperature, Tolerance, Strength and Applications

Feb 19, 2024 Leave a message

Hot rolled steel and cold rolled steel are distinguished by the temperature at which the final deformation takes place, not by the grade of the base metal. The same chemistry can become either product, yet the two differ in thickness range, surface condition, dimensional tolerance, strength and ductility, which is why substituting one for the other in a drawing can change both fit-up and forming behaviour.

How Hot Rolling Works

Hot rolling takes place above the recrystallisation temperature of the steel. The billet or slab is reheated above roughly 1000 °C and passed through a series of rolls that reduce it to plate, sheet or a profile. Because the metal is soft and recrystallises as it deforms, large reductions are achieved in a few passes, so long lengths and heavy sections can be produced at high productivity and at a lower cost per tonne than cold rolled product.

Hot rolled stock is normally supplied from 3 mm thickness upwards for sheet and plate, and as structural sections. Cooling in air leaves a mill scale oxide layer and a slightly rougher surface, and the elevated finishing temperature means dimensional tolerance bands are wider than for cold rolling.

How Cold Rolling Works

Cold rolling is carried out below the recrystallisation temperature, in practice at ambient temperature. It includes cold rolling of sheet and cold drawing of bars, wire and tube, and it is used when accurate size, a smooth surface and higher strength are required. Rolling oil cools the strip and acts as a lubricant; without a stable oil film the work rolls would score the surface and the strip would deform irregularly, which is why cold rolled coil is recognisable by its oily, bright finish.

Mild steel is commonly cold rolled to 0.5-3 mm and stainless steel to 0.5-5 mm. Thinner gauges increase roll loads and springback, so the process needs tighter mill control and more passes than hot rolling.

Property Comparison

Item Hot rolled Cold rolled
Working temperature Above recrystallisation, billet over 1000 °C Below recrystallisation, effectively room temperature
Thickness range From about 3 mm upward About 0.5-3 mm mild steel, 0.5-5 mm stainless
Surface Mill scale, dull, rougher Bright, oily, smooth
Dimensional tolerance Wider bands Tight, consistent thickness
Yield strength Lower, annealed condition Raised by work hardening
Ductility and toughness Higher Lower, less elongation
Residual stress Low Significant if not annealed
Cost per tonne Lower Higher

Microstructure and Mechanical Behaviour

Because hot rolling finishes above the recrystallisation temperature and then cools in air, the microstructure is recrystallised and relatively uniform, with good ductility and notch toughness. Cold rolling instead multiplies dislocations without allowing recovery, so the grains elongate in the rolling direction and the material work hardens: yield strength and hardness rise while elongation falls. A cold rolled coil is therefore often supplied in annealed or skin-passed condition to restore formability while keeping a controlled surface.

Two consequences matter in fabrication. First, cold rolled material exhibits more springback, so press brake angles need compensation. Second, residual stresses can cause distortion when a part is cut or welded unless the strip was stress relief annealed.

Standards and Tolerances

Hot rolled structural steel: EN 10025-2 grades such as S235JR and S355JR.

Hot rolled carbon sheet and strip: ASTM A1011 and ASTM A568 general requirements.

Hot rolled plate: GB/T 3274, with Q235B and Q355B grades to GB/T 700 and GB/T 1591.

Cold rolled carbon sheet: ASTM A1008 and EN 10130 DC01 to DC07 drawing grades.

Cold rolled dimensions and shape: GB/T 708.

Choosing Between the Two

Select cold rolled when the part is visible, when thickness must be tightly controlled, when high strength from work hardening is useful, or when the surface will be painted, coated or plated. Select hot rolled when the section is thicker than about 3 mm, when the part will be heavily formed or welded, when notch toughness matters, or when cost and availability dominate. Both routes can be supplied with certified chemical composition and mechanical test results.

Frequently Asked Questions

Q: Is cold rolled steel stronger than hot rolled steel?
It normally has a higher yield strength because of work hardening, but lower elongation. Hot rolled product is more ductile and easier to form and weld.

Q: Can hot rolled steel be cold rolled afterwards?
Yes. Hot rolled pickled coil is a common feedstock for cold rolling, with the oxide layer removed first so the rolls do not press scale into the surface.

Q: Why does cold rolled steel look oily?
The rolling oil lubricates the strip and controls friction between roll and steel. A residual oil film is a normal feature of the as-rolled surface and is removed before painting.

Q: Are the thickness limits fixed?
No. They are practical ranges. Hot rolling can go below 3 mm in some mills and cold rolling can exceed 5 mm with sufficient mill power, but cost rises sharply outside the usual bands.

Q: Does hot rolling affect the steel grade?
Chemistry is set at steelmaking. Rolling temperature and cooling control the microstructure, so a grade can meet its specified properties only if the rolling schedule suits it.

Q: Which product should be specified for welded structures?
Hot rolled, in most cases. Its lower residual stress and higher ductility reduce cracking risk, and mill scale is removed by blast cleaning before welding if required.

Send Inquiry