Knowledge

What is SA387 Grade 22 Class 1?

Jan 08, 2026 Leave a message

What is SA387 Grade 22 Class 1?

 

info-630-314

SA387 Grade 22 Class 1 is a chromium-molybdenum (Cr-Mo) alloy steel plate specifically designed and standardized for the construction of welded pressure vessels and high-temperature components in demanding industrial applications. Its defining characteristic is its annealed heat treatment condition.

 

Key Characteristics

Composition: The 2.25Cr-1Mo alloy provides a superior balance of:

High-Temperature Strength & Creep Resistance (better than lower-alloy grades like Grade 11).

Excellent Resistance to Hydrogen Attack (HTHA) at elevated temperatures.

Good Oxidation and Corrosion Resistance.

Condition & Properties (As-Supplied):

Annealed State: Furnace cooled to produce a soft, ductile microstructure.

Mechanical Result: Relatively lower yield and tensile strength but very high ductility and toughness.

Purpose of Annealing: To maximize formability. It can withstand severe cold forming (e.g., rolling, dishing of heads) without cracking during fabrication.

Fabrication Requirement: After welding and forming, the component must undergo a mandatory Post-Weld Heat Treatment (PWHT). This PWHT (typically ~1250°F / 675°C) relieves stresses and tempers the steel, developing its final in-service strength and properties.

Primary Applications

It is used where fabrication complexity demands high formability in a high-performance alloy. Typical uses include:

Hydroprocessing Reactors (Hydrocrackers, Hydrotreaters) in refineries.

High-Temperature & High-Pressure Heat Exchangers.

Power Boiler Components and other pressure vessels in fossil and nuclear power plants.

Chemical Reactors operating in aggressive, hot environments.

 

 

Equivalents for ASME SA387 Grade 22 Alloy Steel Plates

BS EN ASTM/ASME DIN
622-515B 10 CRMO910 SA387-22-1 10 CRMO910


 

Specifications for ASME SA387 Grade 22 Alloy Steel Plates
Chromium & Molybdenum content (according to the ASME specification)

Designation Nominal Chromium
Content (%)
Nominal Molybdenum
Content (%)
SA387 Grade 22 2.25% 1.00%


Tensile Requirements for ASME SA387 Grade 22 Alloy Steel Plates Class 1 Plates

Designation: Requirement: Grade 22
SA387 Grade 22 Tensile strength, ksi [MPA] 75 to 100 [515 to 690]
  Yield strength, min, ksi [MPa]/(0.2% offset) 45 [310]
  Elongation in 8 in. [200mm], min % ...
  Elongation in 2 in. [50mm], min, % 18
  Reduction of area, min % 45 (measured on round specimen)
40 (measured on flat specimen)


Chemical Requirements for ASME SA387 Grade 22 Alloy Steel Plates

Element   Chemical Composition (%)
    SA387 Grade 22
Carbon: Heat Analysis: 0.05 - 0.15
  Product Analysis: 0.04 - 0.15
Manganese: Heat Analysis: 0.30 - 0.60
  Product Analysis: 0.25 - 0.66
Phosphorus: Heat Analysis: 0.035
  Product Analysis: 0.035
Sulphur (max): Heat Analysis: 0.035
  Product Analysis: 0.035
Silicon: Heat Analysis: 0.50 max
  Product Analysis: 0.50 max
Chromium: Heat Analysis: 2.00 - 2.50
  Product Analysis: 1.88 - 2.62
Molybdenum: Heat Analysis: 0.90 - 1.10
  Product Analysis: 0.85 - 1.15

 

 

In summary: SA387 Grade 22 Class 1 is the formable, annealed version of the classic 2.25Cr-1Mo alloy steel, chosen specifically to facilitate the manufacturing of complex, high-integrity pressure vessels for the most severe high-temperature and hydrogen-service environments.

 

 

 

Contact now

 

 

What is SA387 Grade 22 Class 1?
SA387 Grade 22 Class 1 is an annealed chromium-molybdenum alloy steel plate designed for high-temperature pressure vessel service, with a composition of 2.25% Cr and 1% Mo to resist oxidation and hydrogen attack in refinery and power plant applications.

What are the mechanical properties of SA387 Grade 22 Class 1?
In its annealed condition, SA387 Grade 22 Class 1 typically has a tensile strength of 415-585 MPa (60-85 ksi), a minimum yield strength of 205 MPa (30 ksi), and high ductility, making it suitable for severe forming before final heat treatment.

Where is SA387 Grade 22 Class 1 commonly used?
It is widely used in hydroprocessing reactors, hydrocrackers, heat exchangers, and high-temperature pressure vessels in the petrochemical and power generation industries, especially where resistance to hydrogen attack and creep is required.

How does SA387 Grade 22 Class 1 differ from Class 2?
Class 1 is supplied in an annealed state for better formability, while Class 2 is normalized and tempered for higher as-delivered strength. Class 1 is chosen when complex fabrication is needed before final PWHT.

What is the post-weld heat treatment (PWHT) for SA387 Grade 22 Class 1?
PWHT is mandatory and typically performed at 1250-1300°F (675-705°C) to relieve welding stresses, prevent hydrogen-induced cracking, and restore corrosion resistance in the weld zone for high-temperature service.

What are the equivalent materials to SA387 Grade 22 Class 1?
Common equivalents include UNS K21590, European 10CrMo9-10 (1.7380), and the generic designation 2.25Cr-1Mo steel. However, exact equivalency depends on heat treatment and certification requirements.

Can SA387 Grade 22 Class 1 be used in hydrogen service?
Yes, its 2.25% chromium and 1% molybdenum content provides excellent resistance to high-temperature hydrogen attack (HTHA), making it a standard choice for hydrogen processing units in refineries.

What are the forming and machining guidelines for SA387 Grade 22 Class 1?
Due to its annealed condition, it offers good cold formability but requires preheating for hot forming and controlled machining to avoid excessive work hardening, with tooling suitable for alloy steels.

What standards certify SA387 Grade 22 Class 1 plates?
Plates are certified to ASME SA387/SA387M and ASTM A387/A387M standards, with mill test reports (MTRs) providing chemical and mechanical properties per EN 10204 3.1 or 3.2.

How does SA387 Grade 22 Class 1 compare to Grade 11 or Grade 5?
Compared to lower-alloy grades like Grade 11 (1.25Cr-0.5Mo) or Grade 5 (5Cr-0.5Mo), Grade 22 offers superior high-temperature strength and hydrogen resistance, but requires stricter welding and heat treatment controls.

 

Full specification and details are available on request. The above information is provided for guidance purposes only. For specific design requirements please contact our technical sales staff.

info-500-499

 

 

Send Inquiry