Knowledge

JIS G3106 SM400B Structural Steel: Properties and Uses

Oct 30, 2025 Leave a message

SM400B is a carbon structural steel grade covered by JIS G3106, the Japanese Industrial Standard for rolled steels for welded structures. The SM series is one of the most widely used steel families in Japan and across Asia, and SM400B in particular is a general-purpose grade specified for welded structures where both strength and guaranteed impact toughness are required. Because the grade is defined by a Japanese national standard, it is referenced in structural design and fabrication work throughout the region and in international projects that adopt Japanese design practice.

SM400A, SM400B, and SM400C: How They Differ

JIS G3106 defines three SM400 grades, SM400A, SM400B, and SM400C, with the same nominal strength but different additional requirements. The letters A, B, and C do not indicate strength; they mark progressively tighter quality requirements.

SM400A is the base grade, supplied on strength requirements alone, with no mandatory Charpy impact testing.

SM400B adds a guaranteed Charpy impact requirement of 27 J at 0 degrees Celsius, making it suitable for welded structures exposed to near-freezing conditions.

SM400C keeps the same impact requirement as SM400B but applies tighter limits on carbon, phosphorus, and sulfur, which further improves weldability and is preferred for heavy welded fabrications.

For a project that needs guaranteed toughness in a general-purpose carbon steel, SM400B is often the most economical choice, while SM400C is selected where the highest level of weldability is wanted.

Mechanical Properties of SM400B

The mechanical requirements of SM400B depend on the plate or section thickness:

Minimum yield strength: 245 MPa for thicknesses up to 16 mm, reducing to lower values for thicker material as defined in the standard.

Tensile strength: 400 to 510 MPa across the common thickness range.

Elongation: minimum values defined for each thickness range and product form, typically in the range of 17 to 21 percent.

Impact toughness: minimum 27 J at 0 degrees Celsius in the Charpy V-notch test for the thickness range covered by the requirement.

These properties make SM400B comparable to other general structural carbon steels such as ASTM A36 in the United States and the S235 family in Europe, although the exact values and the impact requirement differ, so a direct substitution should always be checked against the design specification.

Chemical Composition and Weldability

SM400B is a low-carbon steel designed for welding. The maximum carbon content is about 0.20 percent for the common thickness range, with a slightly higher limit permitted for thicker material. Manganese is controlled to about 1.40 percent maximum, and phosphorus and sulfur are each limited to low maximum values, typically about 0.035 percent, to keep the steel clean and weldable.

Because the carbon content is low, SM400B can be welded by all the common arc welding processes without special precautions under normal conditions. For heavy sections or highly restrained joints, preheating and interpass temperature control may be recommended, and the welding procedure should be qualified in line with the relevant fabrication code. The steel also forms and machines predictably, which keeps fabrication cost low.

Typical Applications

SM400B is used wherever a dependable welded carbon steel is needed:

Buildings: columns, beams, and bracing in steel-framed buildings and industrial plants.

Bridges: girders, cross-beams, and fabricated members in highway and railway bridges.

Tanks and pressure parts: storage tanks, pressure vessels, and penstocks in general service.

Ships and marine structures: hull plating and structural members where the grade meets the applicable classification requirements.

Machinery and transport: frames and structural parts of cranes, construction equipment, and rail vehicles.

The guaranteed impact toughness of SM400B is an advantage in outdoor structures in temperate climates, where the minimum service temperature may approach 0 degrees Celsius.

Cross-Reference with Other Standards

Because SM400B is a Japanese national grade, it is often compared with equivalent grades from other systems. In American practice it is commonly referenced alongside ASTM A36, and in European practice alongside the EN 10025-2 S235 grades. In China, GB/T 700 Q235B and GB/T 1591 structural grades are frequently considered for similar service. These comparisons are useful for orientation, but they are not exact equivalences: the yield strength, impact requirement, and composition limits differ from standard to standard, so any substitution must be verified against the governing design code and confirmed by the responsible engineer before the material is ordered.

Frequently Asked Questions

What does the SM400 designation mean? SM stands for steel for marine and welded structures under JIS G3106, and 400 refers to the minimum tensile strength of the grade in megapascals, which is 400 to 510 MPa.

What is the difference between SM400A, SM400B, and SM400C? all three have the same strength level. SM400A has no mandatory impact requirement, SM400B guarantees 27 J at 0 degrees Celsius, and SM400C adds the same impact requirement with tighter carbon, phosphorus, and sulfur limits for better weldability.

What is the yield strength of SM400B? The minimum yield strength is 245 MPa for thicknesses up to 16 mm, with reduced values for thicker sections as defined in JIS G3106.

Can SM400B be welded? Yes. SM400B is a low-carbon steel designed for welded structures, and it can be welded by common arc welding processes with qualified procedures and normal precautions for heavier sections.

Is SM400B equivalent to ASTM A36 or S235JR? SM400B is comparable in strength to A36 and the S235 family, but the grades are not identical: SM400B includes a guaranteed impact requirement at 0 degrees Celsius, and the composition limits differ. Substitution should be confirmed against the design specification.

What thickness ranges are covered by JIS G3106? JIS G3106 covers plates, strips, sections, and bars over a wide range of thicknesses, with the mechanical property values and composition limits defined in steps by thickness group in the standard.

Send Inquiry