What are the properties and applications of A387 Grade 12 Class 2?

ASTM A387 Grade 12 Class 2 is a normalized and tempered chromium-molybdenum (1.25Cr-0.5Mo) alloy steel plate designed for high-temperature service in welded pressure vessels and boilers, offering higher strength than Class 1 through its specific heat treatment.
Properties of A387 Grade 12 Class 2
This chromium-molybdenum alloy steel is defined by a balanced set of properties ideal for high-temperature, high-pressure environments.
Key Properties:
Mechanical Strength: It is supplied in the normalized and tempered (N&T) condition, which gives it higher strength compared to its annealed Class 1 counterpart.
Tensile Strength: 485 - 620 MPa (70 - 90 ksi)
Yield Strength (min): 275 MPa (40 ksi)
Elevated Temperature Performance: The primary purpose of its alloying.
Chromium (0.80-1.25%): Provides resistance to oxidation (scaling) and corrosion at high temperatures.
Molybdenum (0.44-0.65%): Enhances strength at elevated temperatures and reduces susceptibility to creep and temper embrittlement.
Fabricability: It has good weldability and formability, but requires strict adherence to preheating (typically 150-250°C / 300-480°F) and mandatory Post-Weld Heat Treatment (PWHT) to prevent hydrogen-induced cracking and restore properties in the weld zone.
Hardness: Typically in the range of 140-207 HBW in the normalized and tempered condition.
Primary Applications of A387 Grade 12 Class 2
This material is a workhorse in industries where equipment operates under sustained high pressure and elevated temperature. Its main applications are in the fabrication of welded pressure vessels and components.
Typical Uses Include:
Petroleum Refining & Petrochemical Plants:
Reactors and vessels in hydroprocessing units (e.g., hydrotreaters, hydrocrackers).
Heat exchangers, separators, and distillation columns handling hot oils and gases.
Power Generation:
Pressure vessels for conventional and nuclear power plants.
Sections of steam boilers and other high-temperature containment systems.
General Process Industries: Any application requiring a cost-effective, readily weldable alloy steel for service temperatures typically up to approximately 540°C (1000°F).
In essence, A387 Grade 12 Class 2 is the standard choice for constructing critical, code-compliant pressure-containing components that must maintain strength and resist degradation in hot, corrosive service environments.
1. What is the typical post-weld heat treatment (PWHT) temperature and hold time for A387 Gr.12 Cl.2?
For A387 Grade 12 Class 2, the typical recommended Post-Weld Heat Treatment (PWHT or stress relief) temperature range is 1100°F to 1250°F (595°C to 675°C). The holding time is usually a minimum of 1 hour per inch (25 mm) of thickness, with a common minimum of 1 hour total. This process is critical to relieve welding stresses, temper the heat-affected zone (HAZ), and restore corrosion resistance, ensuring the integrity of the fabricated pressure vessel component.
2. Why is preheating mandatory before welding A387 Gr.12 Cl.2 steel?
Preheating, typically in the range of 300°F to 450°F (150°C to 230°C), is mandatory for welding A387 Grade 12 Class 2 to prevent hydrogen-induced cracking (HIC), also known as cold cracking. This alloy's hardenability can lead to a brittle microstructure in the weld zone upon rapid cooling. Preheating slows the cooling rate, allowing hydrogen to diffuse out and reducing the risk of forming crack-susceptible martensite, thereby ensuring a sound, defect-free weld.
3. What is the maximum continuous service temperature for A387 Gr.12 Cl.2 plates?
The maximum recommended continuous service temperature for ASTM A387 Grade 12 Class 2 plates is generally up to 1000°F (540°C). At this elevated temperature range, the chromium content provides improved resistance to oxidation (scaling) and corrosion, while the molybdenum enhances strength and reduces creep. For service above this temperature, grades with higher chromium content (like Grade 11 or 22) are typically considered.
Full specification and details are available on request. The above information is provided for guidance purposes only. For specific design requirements please contact our technical sales staff.


