Knowledge

Mechanical Properties of SA36 Steel

Jan 15, 2026 Leave a message

SA36 steel is the ASME Boiler and Pressure Vessel Code designation for carbon structural steel conforming to ASTM A36/A36M, widely used for riveted, bolted, or welded construction of bridges, buildings, and general structures. For practical purposes, the mechanical and chemical requirements of SA36 and A36 are identical, and the grade is a low-carbon mild structural steel whose properties are simple and predictable.

What Is SA36 Steel?

The SA prefix indicates that the material is accepted under the ASME Boiler and Pressure Vessel Code, which makes it eligible for non-pressure parts in ASME-coded equipment. SA36 is supplied as hot-rolled plates, bars, and structural shapes including beams, channels, and angles. It is a strength-only grade: the base specification does not require Charpy impact testing, so the material is selected where adequate strength, weldability, and economy matter more than guaranteed fracture toughness.

Guaranteed Mechanical Properties

The primary guaranteed minimum values for plates, bars, and shapes up to 8 in (200 mm) thick are:

Property Value (imperial) Value (metric)
Yield strength, min 36,000 psi 250 MPa
Tensile strength 58,000-80,000 psi 400-550 MPa
Elongation, min (8 in / 200 mm) 20% 20%
Elongation, min (2 in / 50 mm) 23% 23%

For shapes and bars over 8 in (200 mm) thick, the minimum tensile strength remains 58,000 psi (400 MPa) and the yield strength is not specified, while the elongation requirement still applies. The exact elongation values depend on the product form and gauge length, as defined in the standard.

Physical and Design Values

The following typical design values apply to SA36 for engineering calculations:

Modulus of elasticity: about 29,000 ksi (200 GPa).

Shear modulus: about 11,200 ksi (77 GPa).

Poisson's ratio: about 0.26.

Density: about 0.284 lb/in3 (7,850 kg/m3).

These are typical values for carbon structural steel and are used in member design and weight calculations.

What Is Not Required

Impact toughness: Charpy testing is not required by the base specification. This is the major difference between SA36 and grades such as S355J2, which guarantee impact properties. Impact testing can be added as a supplementary requirement when the application needs it.

Through-thickness (Z-direction) properties: not specified in the base standard; Z-grade testing can be ordered separately where lamellar tearing resistance is needed.

SA36 Versus European Grades

SA36 is commonly compared with S235JR per EN 10025-2. The two grades are similar in application, but the nominal yield strengths differ: 250 MPa for A36 versus 235 MPa for S235JR for thin sections, so equivalence should be confirmed on a project basis rather than assumed. SA36 has no direct equivalent to higher-strength European grades such as S355, which offer more strength and mandatory toughness options.

SA36 is used for building frames, industrial structures, base plates, machinery frames, brackets, non-critical bridge components, and non-pressure attachments in ASME-coded vessels. Its low carbon content gives excellent weldability and formability, and it remains one of the most economical structural steels for general fabrication.

Frequently Asked Questions

What is the yield strength of SA36? The minimum yield strength is 36 ksi (250 MPa) for plates and bars up to 8 in (200 mm) thick.

What is the tensile strength of SA36? The tensile strength must fall in the range of 58-80 ksi (400-550 MPa).

What is the elongation of SA36? The minimum elongation is 20% in 8 in (200 mm) and 23% in 2 in (50 mm), depending on product form and gauge length.

Does SA36 require impact testing? No. Impact testing is not mandatory in the base specification; it can be specified as a supplementary requirement when the application requires guaranteed toughness.

Is SA36 the same as A36? Yes. A36 is the ASTM structural steel specification, while SA36 is the same material listed in the ASME Boiler and Pressure Vessel Code; the mechanical and chemical properties are identical.

What is SA36 steel equivalent to? It is often compared with S235JR per EN 10025-2, but the yield levels differ slightly (250 MPa versus 235 MPa), so equivalence must be verified against the design requirements.

Send Inquiry