Round Steel: Definition and Delivery Condition
Round steel is a solid bar with a circular cross-section, produced by hot rolling or cold drawing. In commercial practice the term covers hot-rolled bars delivered to GB/T 702-2017, EN 10060 or ASTM A29/A29M, and cold-finished bars delivered to ASTM A108. Four variables drive the purchase specification: nominal diameter, delivery length, dimensional tolerance and surface condition, while the steel grade fixes strength, hardenability and machinability.
Hot-rolled bars normally leave the mill with a scale-covered surface and a diameter tolerance band that widens with size. Cold-drawn or peeled and polished bars are ordered when tight diameter control, better straightness or a bright finish is required, for example on shafting that is subsequently ground.
Main Round Steel Models and Their Standards
The models most frequently traded in export lots are low-carbon structural grades, medium-carbon quality grades, alloy structural grades and bearing grades. Each carries a different combination of strength and hardenability, so the grade selection normally follows the final heat treatment and the service load.
| Model (grade) | Governing standard | Typical diameter range | Typical use |
|---|---|---|---|
| Q235B | GB/T 700-2006 | 6-250 mm | Couplings, base plates, general fabrication |
| 45 (C45 type) | GB/T 699-2015 | 8-200 mm | Shafts, gears, axles after quenching and tempering |
| 40Cr | GB/T 3077-2015 | 10-250 mm | Transmission shafts, studs, connecting parts |
| 42CrMo | GB/T 3077-2015 | 12-300 mm | High-strength studs, gears, large fasteners |
| 20CrMnTi | GB/T 3077-2015 | 16-150 mm | Carburized gears and pinions |
| GCr15 | GB/T 18254-2016 | 10-120 mm | Bearing rings and rolling elements |
| 1045 / 4140 | ASTM A29/A29M | 12-250 mm | Machined parts to inch-series drawings |
| S355JR | EN 10025-2 | 16-200 mm | Structural pins, brackets, welded assemblies |
Bearing grades such as GCr15 are specified with tighter control of segregation and inclusion content because rolling contact fatigue is sensitive to internal defects. Alloy grades such as 40Cr and 42CrMo are ordered to a hardenability or end-quench requirement when the section is large enough for through-hardening to become the limiting factor.
Dimensional Ranges, Lengths and Tolerances
GB/T 702-2017 fixes the dimensional series for hot-rolled round bars together with the permitted deviation on diameter and out-of-roundness; EN 10060 performs the same function for the European market, and ASTM A29/A29M provides the inch-series dimensional and tolerance tables used for North American orders. Cold-finished product to ASTM A108 is available in closer tolerance classes, which is why it is common for parts that will not be machined on the outside diameter.
Straightness, end-cut squareness and the permitted length tolerance should be agreed at the order stage. Bars supplied in random mill lengths of roughly 4-12 m are the norm for hot-rolled material; cut-to-length supply, chamfered ends and ultrasonic testing are add-on requirements that have to be stated explicitly.
Selection Criteria for Procurement
Three questions resolve most round bar specifications. First, is the part welded or machined? Free-machining behaviour favours the medium-carbon quality grades, whereas weldability points to low-carbon structural grades. Second, what section must be through-hardened? This sets the alloy content and therefore the grade family. Third, what surface finish and tolerance class does the finished part require? That decides between hot-rolled, peeled and polished, or cold-drawn supply.
For carbon-equivalent control, the purchaser should state the maximum carbon equivalent value when welding is involved, because the same nominal grade can be produced over a range of chemistry that changes preheat requirements. Mechanical property verification is usually carried out on a test piece taken in accordance with the governing standard, with the test location and orientation recorded on the certificate.
Surface Quality, Testing and Marking
Acceptance of round bar usually involves visual examination for cracks, laps, seams and excessive decarburization, plus dimensional measurement at several positions along the bar. Internal soundness may be checked by ultrasonic testing on alloy and bearing grades. Chemical composition, tensile properties and, where specified, impact energy are reported on a mill certificate to EN 10204 type 3.1.
Marking normally carries the grade, heat number, size and standard designation, either stencilled on the bar or shown on a bundle tag. Heat number traceability should be preserved through the whole chain, because it links the delivered bar to the original test results.
Frequently Asked Questions
Q: What is the difference between round steel and a round bar?
A: The two terms describe the same product. Round steel is the trade name used for circular solid bars, while round bar is the more general designation that also includes cold-finished and precision-ground product.
Q: Which grade is normally used for a shaft that will be quenched and tempered?
A: Medium-carbon quality grades such as 45 to GB/T 699-2015, or alloy grades such as 40Cr and 42CrMo to GB/T 3077-2015, are the usual choice because they develop adequate core strength at the section sizes involved.
Q: What diameter range is available in hot-rolled supply?
A: GB/T 702-2017 covers a dimensional series that in commercial practice runs from about 5.5 mm up to 250 mm and above. Sizes below roughly 16 mm are often supplied as wire rod or cold-drawn bar instead.
Q: Is hot-rolled round bar weldable?
A: Low-carbon structural grades such as Q235B and S355JR are routinely welded. Medium-carbon and alloy grades need preheat and controlled heat input, and the carbon equivalent value should be limited by agreement.
Q: How is straightness specified?
A: Straightness is expressed as a maximum deviation over a stated length, for example millimetres per metre, and is measured on a reference surface. Values should be agreed in the order because mill standard limits differ between hot-rolled and cold-finished product.

