Knowledge

A36 Angle Steel Size Ranges: Equal and Unequal Angles Explained

May 22, 2025 Leave a message

ASTM A36 angle steel is one of the most widely traded carbon steel sections in the world. Because A36 is a specification for mechanical properties rather than for a fixed chemistry, the practical answer to the question of which sizes exist comes from the dimensional tables of ASTM A6/A6M, the general requirements standard that rolled shapes are produced to. This article sets out the equal-angle and unequal-angle size ranges, the standard length and tolerance practice, and the points worth checking when A36 angle is specified for a project.

What ASTM A36 Covers

ASTM A36/A36M is the general specification for carbon structural steel, covering shapes, plates and bars. To qualify, the mill must meet a minimum yield strength of 250 MPa (36 ksi), a tensile strength of 400 to 550 MPa and a minimum elongation of 20 percent in a 200 mm gauge length. Angles produced to A36 are rolled to the size tables and tolerances of ASTM A6/A6M, which is why a size enquiry is always answered against a section table rather than a single chemistry sheet.

A36 is a ferritic carbon steel with low carbon and moderate manganese content, so its carbon equivalent is low and it welds readily with common electrodes without preheat in typical thicknesses. That combination of moderate strength, good ductility and easy fabrication is the reason the grade has remained in use for so long in general structures, frames, supports and bracing.

Equal Angle Size Range

An equal angle has two legs of identical length, and the standard range for A36 covers:

Leg length from 1/2 in (12.7 mm) up to 8 in (203.2 mm)

Thickness from 1/8 in (3.2 mm) up to 1 in (25.4 mm)

Leg steps that are typically 1/4 in in the lighter part of the range, widening to 1/2 in and 1 in steps for the heavier legs

Thickness steps that are usually 1/8 in in the small sizes and 1/4 in or greater in the largest legs

The small end of the range serves light-duty work such as furniture frames, shelving, guard rails and residential bracing, while the heavy end is used for industrial frames, crane supports and large building structures where the angle acts as a primary load path.

Unequal Angle Size Range

An unequal angle has legs of different lengths, which suits asymmetric connections, wider seating faces and edge conditions where a standard equal angle will not fit. The common A36 range runs from 2 in x 1.5 in up to 8 in x 6 in, with thickness generally between 1/4 in and 3/4 in across the heavier long-leg combinations. Intermediate combinations such as 3 in x 2 in and 5 in x 3.5 in are widely stocked and are frequently chosen when a bolt group needs more edge distance on one leg only.

Representative Sizes and Nominal Mass

The table below lists representative equal-angle sizes with their nominal mass, which is the value used for ordering, freight estimates and erection planning. Metric conversions are given to the nearest practical figure.

Size (inch) Metric equivalent Nominal mass
L 2 x 2 x 1/8 50.8 x 50.8 x 3.2 mm about 3.19 lb/ft, about 4.75 kg/m
L 3 x 3 x 1/4 76.2 x 76.2 x 6.4 mm about 4.90 lb/ft, about 7.29 kg/m
L 4 x 4 x 1/4 101.6 x 101.6 x 6.4 mm about 6.60 lb/ft, about 9.82 kg/m
L 6 x 6 x 3/8 152.4 x 152.4 x 9.5 mm about 14.9 lb/ft, about 22.2 kg/m
L 8 x 8 x 1/2 203.2 x 203.2 x 12.7 mm about 26.4 lb/ft, about 39.3 kg/m

Lengths, Tolerances and Finish

Angle steel is normally supplied in random mill lengths of 20 ft (6.1 m) and 40 ft (12.2 m). Lengths of 30 ft (9.1 m) and fixed cut lengths are also common, with saw-cut tolerance agreed at order stage. ASTM A6/A6M governs the permissible variation in leg length, thickness, squareness of the section, camber and bow, so a size callout is always read together with that standard rather than in isolation.

Finish is mill finish hot rolled black, hot-dip galvanized, or painted. Where galvanizing is specified, allowance has to be made for coating thickness and for drainage and venting holes in the fabricated item, and the coating standard should be stated on the order so that coating mass per unit area is verifiable.

Metric Equivalents and Substitution

A36 has no direct chemistry equivalent in the European or Chinese systems, but its strength class sits close to S235JR and S235J0 to EN 10025-2 and to Q235B to GB/T 700-2006. Substitution is a commercial decision that has to be checked against the design drawings, because the permitted tensile range, the minimum copper content and the impact requirements differ even where the minimum yield strength is the same. For higher loads the comparison is usually drawn against A572 Grade 50 or Q355B to GB/T 1591-2018 rather than against A36.

Choosing the Right Angle Size

Connection geometry: the leg length must provide adequate edge distance and a workable gauge line for the bolts or welds used.

Thickness: leg thickness drives the shear and bearing capacity of a connection more than any other dimension.

Slenderness: thin legs buckle locally under compression, so a heavier thickness is often more economical than a larger leg.

Exposure: for outdoor, marine or chemical environments, specify galvanizing or increase the section size to provide a corrosion allowance.

Handling and fabrication: a heavier section may need larger lifting equipment and a higher welding heat input, both of which affect site cost.

Frequently Asked Questions

Q: What is the largest A36 angle size available?
Equal angles go up to 8 in x 8 in with thickness up to 1 in, and unequal angles up to 8 in x 6 in. Section sizes above that range are normally fabricated by welding plates rather than rolled.

Q: Are A36 angles available in metric sizes?
The A36 size tables are imperial by origin, so the nominal dimensions are in inches and decimal fractions of an inch. Metric near-equivalents such as 50 x 50 x 5 mm exist under EN and GB standards, but they are separate products with their own tolerances and should not be treated as an automatic swap.

Q: What is the difference between equal and unequal A36 angles?
Equal angles have two identical legs and are the default choice for bracing and framing. Unequal angles have legs of different lengths and are selected when a connection needs a wider face on one side or when the geometry of the joint is asymmetric.

Q: What lengths does A36 angle steel ship in?
Random mill lengths of 20 ft and 40 ft are standard, with 30 ft lengths commonly available. Fixed cut lengths can be supplied to order and are usually quoted with a positive-only length tolerance.

Q: Can A36 angle steel be welded?
Yes. A36 has a low carbon equivalent and welds readily with common low-hydrogen electrodes. Normal practice is to clean the joint, follow a qualified procedure and increase preheat only for heavy sections or highly restrained joints.

Q: Can Q235B be substituted for A36?
The two grades are close in yield strength, and Q235B to GB/T 700-2006 is often proposed as a substitute. The substitution has to be reviewed against the design specification, because tensile range, chemical limits and impact test requirements are not identical between the two standards.

Send Inquiry