Knowledge

W24x94 Hot-Rolled Wide Flange H-Beam: Section Data and Applications

May 23, 2025 Leave a message

What a W24x94 Wide Flange Beam Is

W24x94 is an American standard wide flange (W-shape) H-beam produced by hot rolling. In the W designation the first figure is the nominal section depth in inches and the second is the unit mass in pounds per linear foot, so a W24x94 is a beam with a nominal depth of 24 inches and a weight of about 94 pounds per linear foot, which is approximately 140 kg per metre in metric terms.

The profile is rolled as one piece, so the web and the two flanges are joined by a continuous rolled fillet rather than by a weld. That is why a wide flange section transfers shear between flange and web in a predictable way, and why it is the usual choice for primary load-bearing members such as columns, beams and trusses.

Material Grades and Applicable Standards

W24x94 sections are normally supplied in carbon and high-strength low-alloy structural steels. The three grades most often specified are:

ASTM A36 - general purpose carbon structural steel with a minimum yield strength of 250 MPa (36 ksi), good ductility and easy welding.

ASTM A572 Grade 50 - high-strength low-alloy steel with a minimum yield strength of 345 MPa (50 ksi), selected when the higher strength allows a lighter frame.

ASTM A992 - the standard material for building frames in the United States, with a 345 MPa (50 ksi) minimum yield strength, a controlled yield-to-tensile ratio and a restricted carbon equivalent for reliable welding.

Dimensional tolerances, straightness, camber, sweep and mass tolerance for the rolled shape follow ASTM A6 / A6M, the general requirements standard for rolled structural steel products. A purchase specification for a W24x94 therefore normally combines one of the grades above with ASTM A6 / A6M for the geometric requirements.

Section Availability and Surface Condition

Although W24x94 identifies a single section, the rolling programme around it covers a wide family of H-sections so that each project can be matched with the most economical depth and weight. Typical ranges are shown below.

Parameter Typical range
Section height 100–630 mm
Web width 80–900 mm
Flange width 50–300 mm
Web thickness 5–16 mm
Flange thickness 7–60 mm
Production route Hot rolled
Surface condition Bare or black, galvanized, coated or painted

Heavier sections are commonly supplied bare or black for frames that will be painted or fire protected, while galvanized, coated or painted finishes are used where the beam stays exposed to weather or to a corrosive atmosphere. Length, end preparation and finishing are agreed with each order.

Why the H-Section Geometry Performs Well

High bending stiffness. Material is concentrated in the two flanges far from the neutral axis, so the section develops a large second moment of area for a comparatively low unit weight.

Stable under load. The symmetrical H-shape resists bending and lateral instability in both principal directions, which simplifies bracing design.

Efficient connections. Flat, parallel flange faces make bolted end plates, shear tabs and welded brackets straightforward to fabricate.

Standardised dimensions. Because the section follows a published dimensional standard, designers can rely on tabulated section properties and fabricators can work to routine procedures.

Typical Applications

Columns, beams and trusses in industrial buildings, warehouses and multi-storey frames.

Bridge girders and cross-bracing in bridge construction.

Offshore platforms and other marine engineering structures.

Transmission towers, machine bases, brackets and foundation piles.

Lifting and transport equipment, and heavy plant supports.

Frequently Asked Questions

Q: What do the numbers in W24x94 mean?
The 24 is the nominal depth of the section in inches and the 94 is the unit weight in pounds per linear foot, which is about 140 kg per metre.

Q: How much does a W24x94 beam weigh per metre?
The imperial figure of 94 lb/ft converts to roughly 140 kg/m; the tabulated section mass and its permitted rolling tolerance are given in ASTM A6 / A6M.

Q: Which grades are normally available for this section?
ASTM A36, ASTM A572 Grade 50 and ASTM A992 are the usual choices; grade selection depends on the required yield strength, weldability and the governing design code.

Q: Which standard covers dimensions and tolerances?
ASTM A6 / A6M sets the general requirements for rolled structural shapes, including dimensional tolerances, straightness, camber and mass tolerance.

Q: Is a hot-rolled W-shape different from a welded H-beam?
A hot-rolled section is formed from a single billet with an integral rolled fillet at the web-to-flange junction, whereas a welded H-beam is assembled from plate by welding, which gives more freedom in size but introduces weld seams and heat-affected zones.

Q: What surface finishes can be supplied?
Sections are delivered bare or black, or with galvanized, coated or painted finishes when corrosion protection is required.

Send Inquiry