Knowledge

W10x15 W-Shape Steel: A36, A572 Gr 50, and A992 Options

May 16, 2025 Leave a message

The W10x15 is a light American W-shape structural steel beam, widely used in building and bridge structures where a modest section with efficient proportions is required. The designation follows the American system for wide-flange shapes: W indicates a wide-flange section, 10 is the nominal depth in inches, and 15 is the nominal mass in pounds per foot. The section can be supplied in several structural steel grades, most commonly A36, A572 Grade 50, and A992, depending on the strength and toughness requirements of the project.

Cross-Section Dimensions of W10x15

The principal dimensions of the W10x15 section are:

Nominal depth: 10 inches, with an actual section height of about 254 mm.

Flange width: about 4.0 inches, approximately 102 mm.

Web thickness: about 0.27 inches, approximately 6.9 mm.

Flange thickness: about 0.27 inches, approximately 6.9 mm.

Nominal mass: 15 pounds per foot, equal to about 22.3 kg per meter.

These values are nominal and are subject to the dimensional tolerances of ASTM A6, the general requirements standard for rolled structural shapes. The section is one of the lighter members of the W10 family, which makes it economical for secondary beams, bracing, and light columns.

Material Options

The W10x15 can be specified in three common grades:

A36: a low-carbon structural steel with a minimum yield strength of 250 MPa and a tensile strength of 400 to 550 MPa. It is a general-purpose grade suitable for conventional building support structures, with excellent weldability and formability.

A572 Grade 50: a high-strength low-alloy steel with a minimum yield strength of 345 MPa and a minimum tensile strength of 450 MPa, with typical elongation around 21 percent. It is selected for heavy-load scenarios where higher strength allows lighter or smaller members.

A992: a high-strength structural steel developed for wide-flange shapes, with a minimum yield strength of 345 MPa and a tight strength range, excellent seismic performance, and good weldability. It is commonly used in high-rise buildings and bridge projects.

The choice of grade should be based on the design loads, the fabrication requirements, and the governing structural code. For building frames in American practice, A992 is the default grade for W shapes; A36 is chosen for general fabrication; and A572 Grade 50 is specified where higher strength than A36 is needed in shapes not covered by A992.

Performance Characteristics

The W10x15 offers a practical combination of properties:

Bending resistance: the wide-flange design optimizes stress distribution and is suitable for medium-span beam structures.

Light weight: the low mass per meter reduces the self-weight of the building while meeting conventional bearing capacity requirements.

Welding compatibility: the section supports arc welding and gas-shielded welding processes, facilitating on-site connections.

Stability: the wide-flange geometry provides good lateral stiffness, which reduces the risk of lateral-torsional buckling in beams.

With the A992 or A572 Grade 50 material, the section also provides improved toughness and consistent strength for structural applications.

Typical Applications

The W10x15 is used in a range of structural roles:

Secondary beams and joists in building frames, supporting floors and roofs over moderate spans.

Bracing members and light columns in steel-framed buildings.

Supports for platforms, mezzanines, and equipment in industrial facilities.

Bridge diaphragms and cross-frames where light sections are adequate.

Because of its light weight, the section is also convenient for prefabrication and site assembly, and it is compatible with bolted and welded connections.

Frequently Asked Questions

What does the W10x15 designation mean? W indicates a wide-flange section, 10 is the nominal depth in inches, and 15 is the nominal mass in pounds per foot, equal to about 22.3 kg per meter.

What are the actual dimensions of a W10x15? The actual section height is about 254 mm, the flange width about 102 mm, and the web and flange thicknesses about 6.9 mm each, per the AISC tables.

What steel grades is W10x15 available in? The section is commonly available in A36, A572 Grade 50, and A992, with A992 being the default grade for W shapes in American building practice.

What is the difference between A36 and A992 for this section? 992 has a higher minimum yield strength, 345 MPa versus 250 MPa for A36, a tighter strength range, and controlled chemistry for weldability and seismic performance.

Can a W10x15 beam be welded? Yes. The section supports arc welding and gas-shielded welding processes, and all three material grades have good weldability with standard procedures.

What is W10x15 used for? It is used for secondary beams, bracing, light columns, platform supports, and bridge diaphragms where a light, efficient W section is adequate.

Send Inquiry