Knowledge

The differences between Q345A steel plate and Q355B steel plate steel H beams

Nov 18, 2025 Leave a message

Q345 is a widely used Chinese-designation high-strength low-alloy (HSLA) structural steel series, applied in bridges, heavy machinery, pressure vessels, and general structural components.

info-434-434

Within this family, subgrades A and B differ primarily in their impact toughness requirements, while other mechanical and chemical properties are similar.

 

1. Standards and Equivalents

Primary Standard: GB/T 1591 - Hot-rolled low-alloy structural steels (China)

Approximate International Equivalents: ASTM A572 Grade 50, EN S355 family (similar strength class)

Category: Low-carbon, HSLA structural steel, non-stainless

 

2. Chemical Composition (Representative, wt%)

Element Q345A Q345B Notes
C (Carbon) ~0.12–0.20 ~0.12–0.20 Low carbon preserves weldability
Mn (Manganese) 0.50–1.60 0.50–1.60 Provides strength
Si (Silicon) 0.10–0.50 0.10–0.50 Deoxidation and slight strengthening
P (Phosphorus) ≤0.035 ≤0.035 Impurity control for toughness
S (Sulfur) ≤0.035 ≤0.035 Same as above
Cr, Ni, Mo, V, Nb, Ti, B, N Trace Trace Microalloying and TMCP may enhance low-temp toughness for Q345B

Notes:

Q345B achieves higher toughness primarily through microstructural control and tighter process limits.

Both maintain low carbon equivalent for good weldability.

 

3. Microstructure and Processing

As-rolled / Normalized Microstructure: Ferrite–pearlite with possible microalloy precipitates (V, Nb, Ti).

Q345B vs Q345A: Tighter grain size, lower inclusions, and TMCP refine microstructure for higher low-temperature toughness.

Heat Treatments:

Normalizing improves toughness and homogenizes microstructure.

Quenching & tempering rarely applied.

Thermo-mechanical processing (TMCP) helps achieve Q345B's low-temp impact targets.

 

4. Mechanical Properties

Property Q345A Q345B Notes
Yield Strength ~345 MPa ~345 MPa Same nominal yield
Tensile Strength Representative range Similar range Varies slightly with thickness/processing
Elongation (A%) Adequate Similar or slightly higher Ductility maintained
Charpy V-notch Impact Baseline Higher specified energy Key differentiator at designated low temperature
Hardness (HB) Moderate Similar Consistent with HSLA steels

Interpretation:

Both grades deliver the same static strength.

Q345B is preferred when low-temperature brittle fracture resistance is critical.

Ductility and hardness are broadly similar.

 

5. Weldability

Low carbon and controlled alloying yield good weldability for conventional methods.

Q345B may require slightly adjusted preheat/interpass control in thick sections to meet low-temp toughness.

Carbon equivalent formulas (CE, Pcm) are used to determine welding procedures.

 

6. Corrosion and Surface Protection

Non-stainless structural steels: require protection in corrosive environments.

Typical protection: hot-dip galvanizing, zinc-rich primers, epoxy/urethane coatings, powder coatings.

 

7. Fabrication, Machinability, and Formability

Formability: Good for both grades; Q345B's toughness does not reduce bendability.

Machinability: Slightly affected by microalloying, but standard tooling works.

Surface Finishing: Shot-blasting, grinding, painting, or galvanizing; similar procedures for both grades.

 

8. Typical Applications

Q345A Applications Q345B Applications
General beams, channels, plates where standard toughness is sufficient Structural components under low-temperature or high-impact loads
Fabricated welded assemblies in benign environments Crane frames, heavy-duty bridges, offshore platforms, pressure-retaining frames
Economy-driven projects Projects demanding higher low-temp impact performance

 

Q345A: Suitable for ordinary structures where standard toughness suffices; more cost-effective.

Q345B: Conservative choice for cold-service conditions, dynamic loading, or stricter fracture control requirements.

info-503-469

Send Inquiry