What Is Corten B Weather Resistant Steel Plate?
Corten B weather resistant steel plate is a low alloy, hot rolled plate grade whose chemistry is built around copper, chromium and nickel. When the surface is left bare and is repeatedly wetted and dried, those elements promote the formation of a dense, tightly adherent oxide layer, usually called a patina, instead of the loose flaking rust found on ordinary carbon steel. The patina develops quickly during the first months of exposure, then stabilises and acts as a barrier that slows further atmospheric attack to a very low rate.
The grade is normally ordered to the ASTM A588 / ASME SA588 specification, with S355J2W to EN 10025-5 and JIS G 3125 SPA-H used as the equivalent designations in Europe and Japan. Typical applications include architectural facades and cladding, bridge girders and gantries, rail wagons, shipping containers, landscaping walls and outdoor sculpture where a natural weathered finish is required.
Chemical Composition of Corten B Steel Plate
The table below lists the standard heat analysis for the grade. Carbon, phosphorus and sulphur are held low for toughness and weldability, while copper, chromium and nickel are balanced so that the patina forms at a controlled and predictable rate.
| Element | Content, % | Element | Content, % |
|---|---|---|---|
| C | 0.19 max | Cr | 0.40 - 0.65 |
| Si | 0.30 - 0.65 | Ni | 0.40 max |
| Mn | 0.80 - 1.25 | Cu | 0.25 - 0.40 |
| P | 0.035 max | Al | 0.020 - 0.06 |
| S | 0.030 max | V | 0.02 - 0.10 |
The aluminium and vanadium additions act as grain refining elements, keeping the transition temperature low and helping the plate retain toughness after rolling.
Mechanical Properties of Corten B Steel Plate
| Grade | Yield strength ReH, N/mm2 (min) | Tensile strength Rm, N/mm2 (min) | Elongation A50, % (min) |
|---|---|---|---|
| Corten B | 345 | 485 | 19 |
A minimum yield strength of 345 N/mm2 places the grade between ordinary S275 structural steel and higher strength S355 grades, while the 485 N/mm2 minimum tensile strength leaves a comfortable margin for plastic redistribution in bolted and welded frames. Because the material is designed to be used without a paint system, the corrosion allowance that would normally be added to a painted carbon steel design can be reduced, so a thinner plate frequently carries the same load over the design life.
Weldability is good because carbon, sulphur and phosphorus are restricted. The grade is readily joined by shielded metal arc, gas metal arc and submerged arc processes using matching weathering electrodes or filler wires, provided standard preheat and interpass controls are respected for the thickness being welded.
Equivalent Grades and Standards
Buyers often specify the grade name that is familiar in their own market. The designations below are normally offered as equivalents because their chemistry and corrosion performance are close to Corten B:
ASTM A588 Grade B - the United States designation, widely used for bridge and building work.
S355J2W to EN 10025-5 - the European weathering structural steel designation.
JIS G 3125 SPA-H - the Japanese weathering grade used in very large volumes for containers.
BS 4360 WR 50 B - the older British grade still quoted on refurbishment projects.
When a project mixes grades, the buyer should confirm that chemistry, delivery condition and impact test arrangement are all stated on the mill certificate, because two apparently equivalent grades can differ slightly in copper and chromium level, and that difference changes how fast the patina stabilises.
Available Sizes and Supply Condition
| Item | Range |
|---|---|
| Specification | ASTM A588 / ASME SA588 |
| Width | 1500 - 3200 mm |
| Length | 6000 - 12000 mm |
| Thickness | 2 - 460 mm |
| Second hot rolled programme | 3 - 150 mm thickness, 900 - 4100 mm width, 3000 - 18000 mm length |
Plate is supplied hot rolled, normally in the as-rolled condition, and can be cut, bevelled, drilled, plasma cut or laser cut to a drawing. Cut edges should be dressed after thermal cutting so that the patina can develop evenly across the cut face.
Fabrication and Application Notes
Store plate clear of the ground and keep it dry before installation, because standing water in a stack can start corrosion in the gaps between plates.
Weld with weathering consumables so that the joint area weathers to a similar colour as the parent plate.
Detailed design should avoid pockets, ledges and water traps, since the patina only protects where wet and dry cycling occurs.
Where the steel is used in a sheltered position, permanently wet conditions or a chloride-rich marine atmosphere, a protective coating is still advisable.
For concrete contact or buried service the plate must be separated from the environment, as the protective layer cannot form under those conditions.
Frequently Asked Questions
Q: What is the difference between Corten A and Corten B?
Corten A is a weathering grade with higher phosphorus content intended mainly for non-structural cladding, while Corten B is a structural plate grade with a minimum yield strength of 345 N/mm2.
Q: Does Corten B plate need painting?
In an open, freely draining environment the plate can be left bare so that the patina develops naturally; in sheltered, buried or heavily polluted locations a coating system should still be applied.
Q: How long does the patina take to form?
The surface colour normally changes within a few months of exposure and the protective layer becomes stable after roughly 18 to 36 months, depending on climate and rainfall.
Q: Can Corten B plate be welded?
Yes. The restricted carbon, sulphur and phosphorus levels give good weldability, and matching weathering electrodes or filler wires are used so that the weld weathers to the same appearance.
Q: Which thickness range is available?
Plate is commonly supplied from 2 mm up to 460 mm in thickness, with widths of 1500 - 3200 mm and lengths of 6000 - 12000 mm.
Q: What are the minimum mechanical values of the grade?
The minimum yield strength is 345 N/mm2, the minimum tensile strength is 485 N/mm2, and the minimum elongation after fracture is 19%.

