S960QL belongs to the EN 10025-6 family of high yield strength structural steels supplied in the quenched and tempered condition. With a minimum yield strength of 960 MPa it sits near the top of the range used for load-bearing fabrication, and the QL suffix tells the buyer that the steel has been impact tested at a low temperature rather than at room temperature.
Standard Identity and Designation
EN 10025-6 covers flat products of high yield strength structural steels in the quenched and tempered delivery condition. In the grade name S960QL, S stands for structural steel, 960 is the minimum yield strength in MPa, Q indicates quenching and tempering, and L denotes impact testing at minus 40 degrees Celsius. The associated steel number is 1.8933.
Chemical Composition Limits
The standard sets maximum values for the elements below, based on ladle analysis. The tight limits on sulphur, phosphorus and nitrogen, together with micro-alloying additions, give the steel both strength and toughness after heat treatment.
| Element | Maximum (percent) |
|---|---|
| C | 0.20 |
| Si | 0.80 |
| Mn | 1.70 |
| P | 0.020 |
| S | 0.010 |
| N | 0.015 |
| B | 0.0050 |
| Cr | 1.50 |
| Cu | 0.50 |
| Mo | 0.70 |
| Nb | 0.06 |
| Ni | 2.0 |
| Ti | 0.05 |
| V | 0.12 |
| Zr | 0.15 |
Mechanical Properties
For thicknesses from 3 to 50 mm the minimum yield strength ReH is 960 MPa, the tensile strength Rm falls between 980 and 1150 MPa, and the minimum elongation after fracture is 10 percent. The narrow spread between yield and tensile values reflects the controlled tempering treatment: the steel is strong but still has measurable ductility rather than behaving like a brittle material.
Impact Toughness and the QL Suffix
Charpy V-notch energy is verified at three temperatures, so a single grade can be ordered for cold-climate service. Longitudinal specimens must reach 50 J at 0 degrees Celsius, 40 J at minus 20 degrees Celsius and 30 J at minus 40 degrees Celsius. Transverse specimens carry slightly lower requirements of 35 J, 30 J and 27 J at the same temperatures.
Manufacturing Route and Processing
Production follows a clean-steel route: primary melting in a converter or electric arc furnace, ladle furnace refining, vacuum degassing, continuous casting, rolling, non-destructive testing and finally quenching and tempering. Vacuum degassing keeps hydrogen and oxygen low, which reduces the risk of cracking during cutting and welding of a steel at this strength level.
Applications and Fabrication Notes
Typical uses are mobile cranes, lifting and rigging equipment, earthmoving and mining machinery, and highly loaded structural components where weight saving matters. Fabrication should use low hydrogen consumables, controlled heat input and the preheat specified for the thickness and joint design. Stress concentrations, sharp notches and unplanned weld repairs should be avoided, because the toughness of the heat affected zone is the limiting factor in most welded details.
Frequently Asked Questions
Q: What does the QL suffix mean?
A: Quenched and tempered delivery condition with impact testing carried out at minus 40 degrees Celsius.
Q: What is the minimum yield strength of S960QL?
A: 960 MPa for product thicknesses from 3 to 50 mm.
Q: What tensile strength range does the grade deliver?
A: 980 to 1150 MPa, with a minimum elongation of 10 percent.
Q: What is the steel number for S960QL?
A: 1.8933, as listed in EN 10025-6.
Q: Which impact energy is required at minus 40 degrees Celsius?
A: 30 J for longitudinal Charpy V-notch specimens and 27 J for transverse specimens.

