SA514 Grade E

SA514 Grade E: Material Profile
SA514 Grade Eis a high-strength, quenched and tempered alloy steel plate within the ASTM A514/A514M specification, distinguished by its enhanced atmospheric corrosion resistance while maintaining the 100 ksi (690 MPa) minimum yield strength characteristic of the A514 family.
Quick-Reference Specification OF SA514 Grade E
| Category | Specification |
|---|---|
| Standard | ASTM A514 / ASME SA-514 |
| Type | Alloy Steel, Quenched & Tempered (Q&T) |
| Yield Strength (min) | 100 ksi (690 MPa) |
| Key Distinguishing Feature | Higher Molybdenum content for improved corrosion resistance (~2x carbon steel). |
| Primary Niche | High-strength structural applications where some unpainted exposure is expected, but not severe enough to require full weathering steel (A588/A709-W). |
1. Chemical Composition OF SA514 Grade E (Weight %)
The chemistry is optimized for strength, hardenability, and corrosion resistance.
| Element | Requirement (Grade E) | Role / Effect |
|---|---|---|
| Carbon (C) | 0.12 - 0.21% | Base strength and hardenability. |
| Manganese (Mn) | 0.95 - 1.30% | Strength, toughness, and hardenability. |
| Silicon (Si) | 0.40 - 0.80% | Deoxidizer, strengthens ferrite. |
| Chromium (Cr) | 0.40 - 0.65% | Hardenability and corrosion resistance. |
| Molybdenum (Mo) | 0.20 - 0.30% | Key Differentiator. Enhances hardenability, high-temperature strength, and atmospheric corrosion resistance. |
| Boron (B) | 0.0005 - 0.005% | Dramatically increases hardenability cost-effectively. |
| Vanadium (V) | 0.03 - 0.08% | Grain refinement, precipitation hardening. |
| Phosphorus (P) | ≤ 0.035% | Impurity control. |
| Sulfur (S) | ≤ 0.035% | Impurity control. |
2. Mechanical Properties OF SA514 Grade E
Properties are achieved via quenching and tempering.
| Property | Requirement |
|---|---|
| Yield Strength (min) | 100 ksi (690 MPa) |
| Tensile Strength | 115 - 135 ksi (790-930 MPa) |
| Elongation (in 2") | ≥ 18% |
| Charpy V-Notch Impact | ≥ 40 ft-lb (54 J) @ -40°F (-40°C) |
3. Key Advantages & Characteristics OF SA514 Grade E
High Strength & Toughness: 100 ksi yield with excellent low-temperature impact resistance.
Enhanced Corrosion Resistance: Offers approximately twice the atmospheric corrosion resistance of standard carbon steel (e.g., A36) due to its specific alloy balance, particularly the elevated Molybdenum.
Good Hardenability: Capable of maintaining properties in thicker sections (typically up to 4 inches).
Weldable (with care): Requires strict low-hydrogen procedures similar to other A514 grades.
4. Primary Applications OF SA514 Grade E
SA514 Grade E is used in high-strength applications where some environmental exposure is anticipated, but full weathering steel is not specified.
Heavy Equipment for Outdoor Use:
Mining & Construction: Excavator booms, shovel components, and crane structures that are stored or used outdoors but may be repainted or receive some maintenance.
Industrial Structures:
Unpainted or intermittently maintained support frames, platforms, and walkways in industrial plants.
Transportation & Infrastructure:
Specialized trailer frames and components exposed to weather.
Non-bridge structural components where its corrosion resistance is a beneficial bonus.
Energy Sector:
Components for land-based drilling rigs and renewable energy structures.
5. Fabrication Considerations OF SA514 Grade E
| Process | Key Considerations |
|---|---|
| Welding | Strict procedures mandatory. Requires pre-heat (300-400°F/150-200°C), low-hydrogen electrodes, and often Post-Weld Heat Treatment (PWHT). |
| Cutting | Thermal cutting (plasma, laser) is standard. Oxy-fuel cutting requires pre-heat to avoid hard edges. |
| Forming | Cold forming is difficult. Hot forming followed by re-heat-treatment is recommended for severe bends. |
6. Comparison with Key Grades OF SA514 Grade E
| Grade | Key Difference from SA514 Grade E |
|---|---|
| SA514 Grade F | Most common A514 grade. Similar 100 ksi strength but lacks the enhanced corrosion resistance of Grade E (lower Mo). |
| ASTM A709 Grade 100W | True weathering steel for bridges. Has higher corrosion resistance (4-6x carbon steel) and is code-listed for bridges. Strength is identical. |
| ASTM A588 | Standard 50 ksi weathering steel. Used for unpainted, exposed structures. Half the strength of Grade E but better and more predictable corrosion resistance for architectural exposure. |
Important Distinction: Corrosion Resistance Level
It is crucial to understand that SA514 Grade E's corrosion resistance (~2x carbon steel) is intermediate.
It is better than plain carbon steel (A36) or standard high-strength steel (A572).
It is inferior to dedicated weathering steels like A588 or A709-W (~4-6x carbon steel).
Summary
SA514 Grade E is a niche, high-performance steel that bridges the gap between ultra-high-strength structural steel and weathering steel. It is the optimal choice when a designer needs 100 ksi strength and can benefit from moderate, "bonus" corrosion resistance in an exposed application, but where the full specification of a true weathering steel is either unnecessary or cost-prohibitive. Its use is justified in heavy industrial and equipment applications rather than in architectural or bridge contexts, where A588 or A709-W would be the standard.
What distinguishes ASTM A514 GR E from other grades?
GR E excels in low-temperature toughness, making it suitable for cold environments with yields up to 100 ksi under 2.5 inches.
Is welding A514 GR E straightforward?
Yes, with preheating and proper fillers to avoid cracking-our plates are optimized for it.
Key applications plate.
Offshore rigs, mining in cold areas, and structures requiring impact resistance at low temps.
Full specification and details are available on request. The above information is provided for guidance purposes only. For specific design requirements please contact our technical sales staff.


