Knowledge

S355J2 Hot Rolled H-Beam Steel: HEM220 to HEM600 Sizes and Properties

Apr 10, 2025 Leave a message

S355J2 hot rolled H-beam steel is a low-alloy structural section supplied in the European HEM wide flange family, a group of heavy profiles that carry a thicker web and heavier flanges than the standard HEB and IPE ranges. The combination of a 355 MPa minimum yield strength and a guaranteed impact energy at -20 °C makes the grade a frequent choice for heavy building frames, crane girders and structures erected in cold climates. This guide covers the meaning of the designation, the HEM220 to HEM600 size range, the chemical and mechanical limits of EN 10025-2, and the practical rules for cutting, welding and inspection.

Reading the S355J2 and HEM Designations

Under EN 10025-2 the letter S identifies a structural steel, the number 355 is the minimum yield strength in megapascals for the lowest thickness range, and the suffix J2 defines the impact quality class. J2 means that longitudinal Charpy V-notch specimens must absorb at least 27 J when tested at -20 °C. The same specification also offers JR (27 J at +20 °C), J0 (27 J at 0 °C) and K2 (40 J at -20 °C), so the choice of suffix is a decision about service temperature rather than about strength.

HEM is the heaviest of the three European parallel flange beam series. For a comparable depth, an HEM profile has the thickest web and flanges, and therefore the highest mass per metre together with the greatest bending and shear capacity. HEM sections are also narrow in relation to their depth, which makes them convenient where column widths must stay small, and their parallel flanges simplify bolted connections and end plate detailing.

HEM220 to HEM600: Dimensions and Nominal Mass

Profile Depth h (mm) Width b (mm) Web tw (mm) Flange tf (mm) Nominal mass (kg/m)
HEM220 240 226 15.5 26 117
HEM240 270 248 18 32 157
HEM300 340 310 21 39 238
HEM400 432 307 21 40 256
HEM500 524 306 21 40 270
HEM600 620 305 21 40 285

Dimensions follow EN 10365 and the nominal mass is calculated at a steel density of 7,850 kg/m3, while shape and mass tolerances are governed by EN 10034. A frequent source of confusion in quotations is the mass of HEM220, which is 117 kg/m; the value of 157 kg/m belongs to the larger HEM240 profile. Because HEM beams are ordered by profile designation rather than by weight, the nominal mass should always be confirmed against the dimensional table used for the enquiry.

Chemical Composition and Mechanical Properties of S355J2

EN 10025-2 sets the following limits on ladle analysis for S355J2 in the long product range.

Element C Si Mn P S Cu N
Limit (%) max 0.22 max 0.55 max 1.60 max 0.030 max 0.030 max 0.55 max 0.012

Yield strength ReH: min 355 MPa up to 16 mm, min 345 MPa from 16 to 40 mm, min 335 MPa from 40 to 63 mm, min 325 MPa from 63 to 80 mm, min 295 MPa from 100 to 150 mm

Tensile strength Rm: 470 to 630 MPa up to 100 mm thickness, 450 to 600 MPa from 100 to 150 mm

Elongation A: min 22 % up to 40 mm, min 21 % from 40 to 63 mm, min 20 % above 63 mm

Impact energy: min 27 J at -20 °C, Charpy V-notch, longitudinal specimens

Delivery condition: as rolled for the standard product, with normalised or normalised rolled supply available on request

Low-Temperature Toughness, Rolling and Welding Practice

Because the J2 class is verified at -20 °C, an S355J2 beam keeps useful fracture resistance well below the temperatures at which a plain carbon structural beam of similar strength would become brittle. The property depends on fine grain size and clean steelmaking rather than on alloy content, so the impact result is controlled through the rolling schedule, the aluminium or niobium additions used for grain refinement, and the sulphur level that governs inclusion shape.

In fabrication, the heavy web and flange of HEM sections mean that heat input has to be managed more carefully than in thin IPE work. Low-hydrogen consumables and a controlled preheat, typically in the 100 to 150 °C range for thick flanges or high restraint joints, keep the heat affected zone outside the brittle range, while a moderate heat input preserves the grain refinement that gives the grade its toughness. Flame cutting and plasma cutting are both used, and cut edges of thick flanges are normally dressed before welding. Where the section will be galvanised, correct vent and drain holes have to be detailed at the drawing stage so that molten zinc can escape.

Typical Applications of S355J2 HEM Beams

Heavy HEM beams in S355J2 are used for crane runway girders and crane columns, for transfer girders carrying heavy point loads, for the primary frames of industrial halls and for bridge and viaduct elements that remain in service through winter conditions. They also appear in port handling equipment, mining and quarry plant structures, and in the support frames of large tanks where both stiffness and low-temperature toughness are required. In each case the section is selected for its stiffness and shear capacity, while the S355J2 quality class is selected for the lowest expected service temperature of the site.

Frequently Asked Questions

Q: What does J2 mean in S355J2?
J2 is the impact quality class: a longitudinal Charpy V-notch specimen must absorb at least 27 J at a test temperature of -20 °C.

Q: What is the difference between HEM220 and HEM240?
HEM220 measures 240 x 226 mm with a 15.5 mm web and a 26 mm flange at a nominal mass of 117 kg/m, while HEM240 measures 270 x 248 mm with an 18 mm web and a 32 mm flange at 157 kg/m.

Q: Can S355J2 be welded without preheat?
Thin sections can often be welded with normal shop practice, but thick HEM flanges and high restraint joints should use low-hydrogen consumables with a controlled preheat, generally around 100 to 150 °C.

Q: Is S355J2 the same as S355JR?
Both grades have identical strength requirements and differ only in impact testing: S355JR is tested at +20 °C with 27 J minimum, while S355J2 is tested at -20 °C.

Q: Which is tougher, S355J2 or S355K2?
The two are tested at the same temperature of -20 °C, but S355K2 requires a higher minimum absorbed energy of 40 J, so it is preferred for more severe cold climate service.

Q: How is the mass of an HEM beam calculated?
The nominal mass per metre in EN 10365 is based on a density of 7,850 kg/m3 and the nominal cross section, so actual mill weights vary slightly within the tolerance of EN 10034.

Send Inquiry