P355M is a weldable fine-grain steel for pressure purposes, defined in EN 10028-5 (flat products made of steels for pressure purposes, thermomechanically rolled weldable fine-grain steels). Its material number is 1.8821. The designation P indicates a pressure application steel, 355 is the minimum yield strength in megapascals, and M denotes the thermomechanically rolled delivery condition. The grade is widely used in pressure vessel and boiler manufacturing where good weldability and low-temperature toughness are required.
Chemical Composition
The composition of P355M is designed for a fine-grained microstructure and good weldability. Typical maximum limits are:
| Element | Maximum, % |
|---|---|
| Carbon (C) | 0.14 |
| Silicon (Si) | 0.50 |
| Manganese (Mn) | 1.60 |
| Phosphorus (P) | 0.025 |
| Sulfur (S) | 0.010 |
| Nickel (Ni) | 0.50 |
| Molybdenum (Mo) | 0.20 |
| Vanadium (V) | 0.10 |
| Niobium (Nb) / Titanium (Ti) | 0.05 each |
| Nitrogen (N) | 0.015 |
| Cr + Cu + Mo | 0.60 |
| V + Nb + Ti | 0.15 |
The low carbon content keeps the steel readily weldable, while microalloying with niobium, vanadium, and titanium refines the grain structure during thermomechanical rolling.
Mechanical Properties
Yield strength (ReH): minimum 355 MPa for thicknesses up to 40 mm, and 345 MPa for 40-63 mm.
Tensile strength (Rm): 450-610 MPa.
Impact energy (KV, transverse): at least 27 J at -20 deg C, with higher values required at warmer temperatures.
Elongation (A): minimum 22% on a 50 mm gauge length for the thinner range, with values by thickness per the standard.
The guaranteed impact energy at -20 deg C is the property that distinguishes P355M for low-temperature pressure service.
Thermomechanical Rolling Process
P355M is produced by thermomechanical rolling (TMR): the plate is heated to about 1050-1150 deg C and hot rolled with precise deformation control, then cooled with accelerated cooling (ACC) to refine the grain size and form a uniform fine-grained microstructure. This process develops the required strength and toughness without a subsequent normalizing treatment, which shortens production cycles and reduces cost while maintaining consistent properties.
Fabrication Guidance
Welding: compatible with SMAW, GMAW, SAW, and FCAW. Preheating to 50-100 deg C is usually applied to prevent cold cracking, and post-weld heat treatment is not necessary for most applications.
Forming: good cold and hot formability. Hot forming at 800-900 deg C reduces forming resistance for bending, stamping, and forging; cold forming is feasible for thin to medium plates with suitable bend radii.
Machining: satisfactory machinability with standard tooling; moderate cutting speeds and feed rates are recommended for accuracy and tool life.
Surface treatment: shot blasting, pickling, painting, or galvanizing are used depending on the service environment.
Applications
Pressure vessels, storage tanks, and reactors for oil, gas, chemical, and petrochemical service.
Boilers, heat exchangers, and steam piping in power generation.
Large-diameter pipelines for water, oil, and gas transport, including outdoor long-distance lines.
Load-bearing components of construction, mining, and port machinery, and large steel structures.
Offshore platforms, ship structures, and marine pipelines exposed to low temperatures and salt spray.
Frequently Asked Questions
What is P355M steel? P355M (1.8821) is a weldable fine-grain pressure vessel steel per EN 10028-5, delivered in the thermomechanically rolled condition, with a minimum yield strength of 355 MPa and guaranteed impact energy at -20 deg C.
What is the difference between P355M and P355N? Both are 355 MPa pressure vessel steels, but P355M is thermomechanically rolled while P355N is normalized. P355M is typically guaranteed at -20 deg C, while P355N impact testing is specified at warmer temperatures, so P355M suits colder service.
Can P355M be used for low-temperature pressure vessels? Yes. Its guaranteed Charpy impact energy at -20 deg C makes it suitable for low-temperature pressure equipment, within the limits set by the governing pressure vessel code.
Does P355M require post-weld heat treatment? Post-weld heat treatment is not necessary for most applications. Where it is required by the design code, stress relief annealing in the range of 550-650 deg C with slow cooling is commonly used.
Is P355M corrosion resistant? P355M has basic atmospheric corrosion resistance but is not intended for aggressive media such as acids or salts. Painting, galvanizing, or other protective systems are normally required for long-term service.
Which standard applies to P355M? P355M is defined in EN 10028-5, the standard for thermomechanically rolled weldable fine-grain steels for pressure purposes. Inspection follows EN 10028-5 requirements including composition, mechanical testing, impact testing, and non-destructive examination where specified.

