JIS G 3106 SM490YA is a welded structural steel plate specified under the Japanese Industrial Standard for rolled steels for welded structures. The grade combines a specified minimum yield strength with a tight tensile window, which makes it suitable for load-bearing welded fabrications such as bridge girders, building frames, plant structures and heavy machinery bases.
JIS G 3106 covers hot rolled steel plates, sheets and strips intended for welded structures. Within that standard, the SM490 family is the higher-strength group: while SM400 grades are built around a 400 MPa tensile range, SM490 grades are built around a 490 MPa tensile range with a correspondingly higher yield requirement.
The grade designation carries useful information. The letters SM indicate structural steel for welded structures, the number 490 indicates the minimum tensile strength class in megapascals, and the suffix letters identify the impact-test category of the grade. SM490YA is the variant for which a Charpy impact energy result is not mandatory at the point of delivery, and impact testing can be ordered on request when the project specification calls for it.
Chemical Composition
SM490YA is a low-carbon, manganese-silicon steel with tightly controlled residuals. The table below gives the typical maximum content in percent by heat analysis.
| Element | C (max) | Si (max) | Mn (max) | P (max) | S (max) |
|---|---|---|---|---|---|
| JIS G 3106 SM490YA | 0.20 | 0.55 | 1.60 | 0.035 | 0.035 |
The low carbon content keeps the heat-affected zone tough after welding, while manganese and silicon raise strength through solid solution and grain refinement. Restricting phosphorus and sulphur reduces hot cracking risk and embrittlement, which is why the residual limits matter more on a welded structure than on a plain carbon plate. When a maximum carbon equivalent is written into the purchase order, the value is determined and reported on the mill test certificate.
Mechanical Properties
Mechanical requirements are specified against product thickness, because yield strength and ductility both vary with section size.
| Property | Thickness range | Requirement |
|---|---|---|
| Yield strength (min) | t 16 mm and below | 365 MPa |
| Tensile strength | t 16 mm and below | 490-610 MPa |
| Elongation (min) | t 16 mm and below | 19% |
Thicker sections are covered by the reduced yield steps set out in JIS G 3106, and the applicable value should always be taken from the standard table for the ordered thickness. The combination of a 365 MPa minimum yield with a 490-610 MPa tensile window gives designers a predictable strength reserve for members carrying static and dynamic loads, while the elongation requirement preserves the ductility needed for seismic and fatigue-sensitive details.
Size Range and Delivery Condition
SM490YA plate is produced by hot rolling and is available across a wide dimensional envelope:
Thickness: 4 mm to 400 mm
Width: 1000 mm to 4000 mm
Length: 4000 mm to 12000 mm
Supply condition: as-rolled, normalised, or quenched and tempered, depending on the required strength and toughness combination
Supplementary options: specified impact testing, hydrogen-induced cracking (HIC) testing, ultrasonic examination and third-party inspection
Controlled rolling is used on thinner and medium sections to obtain the required grain refinement without a separate normalising treatment. Where the design requires guaranteed notch toughness at low temperature, the plate can be ordered with impact testing at 0, -20 or -40 degrees Celsius, with the energy requirement agreed between buyer and supplier before rolling.
Welding and Fabrication
SM490YA is intended for welded construction and is normally welded with conventional processes without preheat on thin and medium sections. Recommended practice includes:
Use electrodes and welding consumables matched to the 490 MPa strength class, keeping hydrogen levels low for thick sections.
Apply preheat and interpass temperature control on heavy thicknesses, restraint-intensive joints and low ambient temperatures.
Keep heat input within the qualified range so that the heat-affected zone retains its toughness.
Maintain the carbon equivalent of the base metal within the limit stated on the certificate.
Carry out post-weld inspection appropriate to the joint class, including ultrasonic or radiographic examination where specified.
The steel is also readily cut by plasma, oxy-fuel or laser, formed by cold bending within the recommended radius for the thickness, and drilled or machined with standard carbide tooling.
Quality Control and Typical Applications
Each heat is checked by ladle analysis against the chemical limits, and mechanical testing covers tensile properties on the rolled product. Dimensional inspection follows the tolerance requirements of JIS G 3106 for thickness, width, length, camber and flatness, and plates are normally supplied with a mill test certificate traceable to the heat number.
Typical uses include bridge and viaduct girders, building columns and beams, roof and floor framing in industrial buildings, transmission and communication towers, offshore and port structures, storage tank supports, pressure-retaining structural components and bases for heavy machinery and cranes. In each case the grade is selected because the welded detail requires a predictable yield strength together with toughness that survives field welding.
Frequently Asked Questions
Q: What does the YA suffix in SM490YA mean?
The letter group after the strength class identifies the impact-test category of the grade. SM490YA is the variant for which a Charpy impact test result is not mandatory at delivery, and impact testing at a specified temperature can be ordered as a supplementary requirement.
Q: What is the yield strength of SM490YA plate?
For thickness of 16 mm and below the specified minimum yield strength is 365 MPa, with a tensile strength of 490-610 MPa and minimum elongation of 19 percent. Values for thicker sections are taken from the JIS G 3106 thickness table.
Q: Can SM490YA be welded without preheating?
On thin and medium sections with controlled heat input, low-hydrogen consumables and reasonable ambient temperature, preheat is often unnecessary. Thick sections, high restraint joints and cold weather normally require preheat and interpass temperature control.
Q: How does SM490YA differ from SM400C?
Both are welded structural steels under JIS G 3106. SM490YA is the higher-strength grade with a 490-610 MPa tensile range and 365 MPa minimum yield, while SM400C offers 400-510 MPa tensile strength with guaranteed low-temperature impact toughness.
Q: Is impact testing available for SM490YA?
Yes. Impact testing at 0, -20 or -40 degrees Celsius can be specified, which is common for structures exposed to low service temperatures or dynamic loading.
Q: What plate sizes are available?
Thickness from 4 mm to 400 mm, width from 1000 mm to 4000 mm and length from 4000 mm to 12000 mm, in the supply condition agreed at order stage.

