Knowledge

Q235 Steel Grade: Properties, Weldability and Grade Selection Guide

Nov 24, 2025 Leave a message

How the Q235 Grade Family Is Organised

Q235 is a carbon structural steel defined by GB/T 700-2006. The designation reads as yield strength: the letter Q stands for the minimum yield strength of the steel and 235 is that value in megapascals for the thinnest product range. Within the grade, four quality classes are defined by metallurgical quality: Q235A, Q235B, Q235C and Q235D. All four share the same nominal strength class, and they differ in how tightly sulphur and phosphorus are controlled and in the temperature at which toughness is verified by a Charpy impact test.

Class Impact test temperature Practical meaning
Q235A No impact test required General welded and non-welded work in mild conditions
Q235B Plus 20 degrees C Room temperature toughness verified
Q235C Zero degrees C For colder service where room temperature testing is not enough
Q235D Minus 20 degrees C Low temperature service with the tightest impurity control

The classes are not interchangeable in cold climates. A member detailed in Q235D for a low temperature location should not be supplied as Q235A simply because the yield strength is nominally the same, because the impact performance is a different property altogether.

Chemical Control That Separates the Four Classes

The four classes differ mainly in the control of sulphur and phosphorus, the two elements that most affect toughness and weldability. Sulphur content falls progressively from A through D, because sulphur forms inclusions that reduce ductility and increase the risk of cracking. Phosphorus is the same in A and B, is held lower in C and reaches its lowest level in D, since phosphorus raises strength but embrittles the steel. Carbon and manganese are broadly comparable across the family, with carbon typically held to roughly 0.22 % maximum in Q235A and Q235B and lower in the C and D classes, and manganese generally limited to about 1.40 % maximum.

The practical effect of this chemical control is that the higher classes weld more reliably in restrained joints and in thicker sections, where the risk of cold cracking is greater. Buyers specifying a class should state it explicitly in the purchase order along with the product thickness range, or accept that the mill may supply the most economic class that meets the strength requirement.

Mechanical and Physical Properties

The values below are the figures normally quoted for Q235 in the hot rolled condition. Yield strength is thickness dependent: the 235 MPa minimum applies to the thin end of the product range and steps down as plate or section thickness increases, so the thickness range must always be quoted alongside the strength figure.

Mechanical property Typical value
Yield strength 235 MPa minimum in the thin product range
Tensile strength 375-500 MPa
Elongation 26 % minimum
Impact energy 27 J minimum at the class test temperature
Hardness about 201 HB maximum in the hot rolled condition
Physical property Value
Density 7.85 g/cm3
Melting range 1420-1460 degrees C
Thermal conductivity 51.9 W/(m K)
Coefficient of linear expansion at 20 degrees C 11.7 micrometres per metre per kelvin

These figures are design aids rather than guarantees. Actual properties vary with heat treatment, rolling practice and heat to heat variation, so the mill certificate for the delivered lot remains the controlling document.

Weldability, Forming and Machining

Q235 welds readily with arc, resistance and gas processes using standard consumables, which is why it is used so widely for fabricated frames, brackets, supports and general structures. Low carbon and controlled sulphur keep the heat affected zone sound, and the higher classes are preferred for restrained joints and for joining to thicker members. Preheating is generally unnecessary at small thicknesses but becomes relevant for thick sections, low ambient temperature or high restraint.

Ductility is the other practical advantage. Q235 tolerates plastic deformation before fracture, so it bends, rolls, shears and punches easily, and it machines well by turning, drilling and milling. The combination of easy forming and predictable welding is what makes the grade a default choice for general engineering work rather than for a specific duty.

Corrosion Protection and Typical Applications

Q235 is not inherently corrosion resistant. In exposed service it relies on a protective system: hot dip galvanizing, zinc rich primers, organic coatings, or a combination of these. Painted protection must cover cut edges, drilled holes and welded zones that are made after coating, because these are where breakdown starts. Where a permanent protective layer is essential, a galvanized or stainless variant of the material family is the more appropriate selection than additional paint thickness.

Typical applications include building and industrial frames, transmission and support structures, machinery bases, storage and shelving, agricultural equipment, general fabrication and non-critical pressure parts. The grade is chosen when moderate strength, excellent fabrication behaviour and low cost matter more than high strength or corrosion resistance.

Frequently Asked Questions

Q: What does Q235 mean?
Q stands for yield strength and 235 is the minimum yield value in MPa for the thin product range. It is a Chinese carbon structural steel grade defined in GB/T 700-2006.

Q: What is the difference between Q235A, B, C and D?
They share a nominal strength class but differ in sulphur and phosphorus control and in impact test temperature, from no impact requirement in A to minus 20 degrees C testing in D.

Q: Is Q235 equivalent to S235JR?
Q235B is often treated as a close counterpart to S235JR in European practice, and Q235A to S235JR without impact testing. Equivalence is not automatic, so the design requirements and impact class should be compared before substitution.

Q: Can Q235 be welded?
Yes. It is readily welded by arc, resistance and gas processes with standard consumables. Thick sections, high restraint and low ambient temperature are the situations where preheat and procedure control matter.

Q: Is Q235 corrosion resistant?
No. Unprotected Q235 will rust in normal atmospheres and requires galvanizing, painting or a similar protective system, with attention to cut edges and welds.

Q: Why is the yield strength sometimes quoted below 235 MPa?
Because the guaranteed minimum is thickness dependent. As plate or section thickness increases the required minimum yield strength steps down, so strength must always be read together with the thickness range.

Send Inquiry