1. Introduction
Q235 steel is one of China's most widely used low-carbon mild steels, primarily composed of iron with a small percentage of carbon (0.12–0.20%) and other alloying elements such as manganese, silicon, and phosphorus. Its low carbon content provides excellent ductility, toughness, and weldability, making it a versatile choice for structural and engineering applications.
Key Advantages:
Cost-effective: Economical for large-scale construction and manufacturing projects.
Versatile: Suitable for structural components, machinery parts, and general fabrication.
Easy to Fabricate: Can be welded, cut, and formed without special equipment.
Limitations:
Corrosion Resistance: Moderate; requires protective coatings for harsh or marine environments.
Strength: Adequate for most applications but lower than higher-grade steels.
Historically, Q235 has been a foundational material in bridges, buildings, machinery, and infrastructure projects across China.
2. Standards and Equivalents
| Standard Organization | Designation / Grade | Region / Origin | Notes |
|---|---|---|---|
| UNS | G3101 Q235 | China | Closest to ASTM A36 |
| ASTM | A36 | USA | Minor compositional differences |
| EN | S235JR | Europe | Similar mechanical properties |
| JIS | SS400 | Japan | Comparable yield strength |
| GB | Q235 | China | National standard |
Note: While Q235 is often compared with ASTM A36 or S235JR, slight differences in composition and properties may affect performance in specific applications.
3. Key Properties
3.1 Chemical Composition (wt%)
| Element | Range (%) |
|---|---|
| Carbon (C) | 0.12 – 0.20 |
| Manganese (Mn) | 0.30 – 0.70 |
| Silicon (Si) | 0.10 – 0.40 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.045 |
Notes: Carbon enhances strength and hardness; manganese improves toughness and hardenability; silicon acts as a deoxidizer and contributes to overall strength.
3.2 Mechanical Properties
| Property | Condition | Metric | Imperial | Test Standard |
|---|---|---|---|---|
| Tensile Strength | Hot Rolled | 370 – 500 MPa | 54 – 73 ksi | ASTM E8 |
| Yield Strength (0.2% offset) | Hot Rolled | ≥ 235 MPa | ≥ 34 ksi | ASTM E8 |
| Elongation | Hot Rolled | ≥ 20% | ≥ 20% | ASTM E8 |
| Hardness (Brinell) | Hot Rolled | ≤ 160 HB | ≤ 160 HB | ASTM E10 |
| Impact Strength | -20°C | ≥ 27 J | ≥ 20 ft-lbf | ASTM E23 |
3.3 Physical Properties
| Property | Value (Metric) | Value (Imperial) |
|---|---|---|
| Density | 7.85 g/cm³ | 0.284 lb/in³ |
| Melting Point | 1425–1540°C | 2600–2800°F |
| Thermal Conductivity | 50 W/m·K | 29 BTU·in/(hr·ft²·°F) |
| Specific Heat Capacity | 0.49 kJ/kg·K | 0.12 BTU/lb·°F |
| Electrical Resistivity | 1.7 × 10^-7 Ω·m | 1.7 × 10^-7 Ω·ft |
4. Corrosion and Heat Resistance
Corrosion Resistance:
Atmospheric: Fair (susceptible to rust)
Chlorides: Poor (risk of pitting)
Acids: Poor (not recommended)
Alkaline: Moderate
Heat Resistance:
| Property | Temperature | Remarks |
|---|---|---|
| Max Continuous Service Temp | 400°C / 752°F | Suitable for structural use |
| Max Intermittent Service Temp | 500°C / 932°F | Short-term exposure only |
| Scaling Temperature | 600°C / 1112°F | Risk of oxidation above this temperature |
Note: Q235 retains structural integrity up to ~400°C, beyond which mechanical properties may degrade.

