Knowledge

European Standard H-Beam Theoretical Weight Table: Calculation, kg/m Data and Estimating Tips

May 06, 2025 Leave a message

What a Theoretical Weight Table Is

A theoretical weight table gives the nominal mass per unit length of a steel section, calculated from its nominal dimensions and the density of steel. It is the standard basis for estimating, ordering and comparing European standard H-beams, because the mass of a section is what drives both the material cost and the transport cost of a project.

European wide flange beams are grouped in families that share a profile shape but differ in wall thickness: HEA has the lightest walls for a given height, HEB has thicker web and flange, and HEM is the heaviest of the three. The IPE family is the narrow flange counterpart with the same design logic. A larger nominal size in a family means greater height, flange width and wall thickness together.

How the Weight Is Calculated

The theoretical mass per metre is obtained from the cross-sectional area of the profile:

Mass per metre (kg/m) = cross-sectional area (cm²) x 0.785

Mass per metre (kg/m) = cross-sectional area (m²) x 7850 kg/m³

Total mass (kg) = mass per metre x cut length (m) x number of pieces

The density of steel used in section tables is 7850 kg/m³, equal to 7.85 g/cm³. The cross-sectional area comes from the nominal dimensions of the profile, so the resulting figure is a nominal value rather than a measured one. The tables published with the European section standards also give area, second moment of area, section modulus and radius of gyration, all derived from the same nominal geometry.

Reference Theoretical Weight Table

Nominal masses of commonly ordered hot rolled IPE, HEA and HEB sections:

Section Nominal mass (kg/m) Section Nominal mass (kg/m)
IPE 100 8.1 HEA 200 42.3
IPE 200 22.4 HEB 200 61.3
IPE 300 42.2 HEB 300 117
IPE 400 66.3 HEB 1000 314

The values illustrate the progression inside a family. Moving from IPE 200 to IPE 300 more than doubles the mass per metre, while the HEB series is roughly 45 % heavier than the HEA series at the same nominal height because of its thicker walls. For the deep sizes used in bridges and heavy industry, for example the 1000 x 300 x 19 x 36 profile, the nominal mass of 314 kg/m means that a single 12 m piece weighs about 3.8 tonnes and requires proper lifting and transport planning.

Why Actual Weight Differs from Theoretical Weight

Mill practice and standard tolerances explain most of the difference between a calculated mass and a weighbridge figure:

Dimensional tolerances on height, flange width and thickness, defined for I and H sections in EN 10034, allow the rolled section to be slightly heavier or lighter than nominal.

Corner radii and flange taper are not part of the simple rectangular calculation but are included in the published table values; using hand calculations off nominal rectangles can therefore drift from the table.

Cut length is often nominal: saw kerf, end trimming and handling losses reduce the delivered length compared with the ordered length.

A hot dip galvanized coating adds the mass of the zinc layer, and paint or intumescent systems add their own weight.

For commercial purposes the table value is therefore used for estimation, while the final invoice is normally settled on the actual weight from the mill or the weighbridge, within the tolerance agreed in the order.

Using the Table in Estimating and Purchasing

Build the take-off section by section, multiplying table mass by cut length and quantity rather than averaging the whole structure.

Add a waste factor for offcuts and test pieces, typically a few percent for straightforward frames and more for complex connections.

Convert to tonnes at the end, since European beams are usually ordered and priced per tonne while sections are designed per metre.

Check the delivery programme against rolling availability: very light and very heavy sizes are rolled less frequently, and this affects both lead time and the choice of section.

Keep the density assumption consistent through the estimate; mixing 7850 kg/m³ with handbook values taken at a different density creates small but cumulative errors.

Frequently Asked Questions

Q: How is the theoretical weight of an H-beam calculated?
Multiply the cross-sectional area by the density of steel, 7850 kg/m³, or use the handbook figure of area in cm² multiplied by 0.785 to obtain kilograms per metre.

Q: Why is the actual weight different from the table value?
Rolling tolerances, corner radii, cut length losses and any coating add to or subtract from the nominal mass, so the delivered weight normally differs slightly from the calculated figure.

Q: What is the theoretical weight of HEB 1000?
The 1000 x 300 x 19 x 36 section has a nominal mass of 314 kg per metre, which is about 3.8 tonnes for a 12 m length.

Q: How do I convert kg/m into tonnes for an order?
Multiply the mass per metre by the total length in metres, divide by 1000 to obtain tonnes, then add the agreed waste allowance.

Q: Does galvanizing change the weight of the beam?
Yes. The zinc coating adds to the finished mass, and although the addition is a small percentage it should be carried as a separate line when the tonnage is critical.

Q: Which section families are covered by the European tables?
The IPE narrow flange family and the HEA, HEB and HEM wide flange families, with dimensions and masses listed for each nominal size and height.

Send Inquiry