Knowledge

SPV235 Boiler Steel Plate: Chemical Composition and Properties

Nov 22, 2024 Leave a message

SPV235 is a Japanese pressure vessel and boiler steel plate specified in JIS G3115, combining moderate strength with good toughness and weldability. The grade number refers to a minimum yield strength of 235 MPa for plates up to 50 mm thick, with tensile strength in the range of 400 to 510 MPa. Its chemical composition is tightly controlled, with maximum carbon of 0.18 percent for plates up to 100 mm thick and 0.20 percent for thicker material, together with strict limits on phosphorus and sulfur to preserve weldability and toughness. The sections below review the chemical composition, mechanical properties, and typical service conditions of SPV235 boiler steel plate.

What Is SPV235 Steel?

SPV235 belongs to the JIS G3115 family of steels for pressure vessels, which are used in the fabrication of boilers and other pressurized equipment. The SPV designation indicates pressure vessel steel, and the number 235 refers to the minimum yield strength in megapascals. The grade is produced as plate and is selected where the pressure and temperature duty is moderate and where good weldability keeps fabrication cost down. Its balanced combination of strength, toughness, and corrosion resistance makes it a dependable material for a wide range of equipment.

Chemical Composition

The chemical composition of SPV235 is controlled to keep the steel clean and weldable. For plates up to 100 mm thick, the maximum carbon content is 0.18 percent, with silicon limited to 0.35 percent and manganese to 1.40 percent. Phosphorus and sulfur are each limited to 0.030 percent maximum. For plates over 100 mm thick, the carbon limit is relaxed to 0.20 percent maximum. These tight limits on phosphorus and sulfur minimize the risk of hot cracking and preserve toughness, which is important for pressure-retaining components.

Mechanical Properties

The minimum yield strength of SPV235 is 235 MPa for plates up to 50 mm thick, 215 MPa for plates over 50 mm up to 100 mm, and 195 MPa for plates over 100 mm thick. The tensile strength range is 400 to 510 MPa across the thickness range. This moderate strength level is matched to pressure vessel designs where the governing loads are not extreme, and it allows the steel to be formed and welded without the complications of higher-strength grades. The material maintains stable mechanical properties under complex working conditions and adapts to a variety of service environments.

Applications and Service Conditions

SPV235 is used for boiler shells, pressure vessel bodies, and storage equipment in industries that involve moderate pressure and temperature. Its good toughness allows it to maintain stable performance under complex working conditions, and its corrosion resistance extends the service life of equipment in mildly corrosive environments. The plate is commonly formed into shells and dished ends, then welded into complete vessels. For severe service conditions, higher grades in the JIS G3115 family should be considered.

Welding and Fabrication Notes

SPV235 has good weldability because of its moderate carbon content and low impurity limits. Standard welding processes such as shielded metal arc welding, gas metal arc welding, and submerged arc welding can be used with matching consumables. For thicker plates, preheating and controlled heat input are recommended to avoid hydrogen-induced cracking. Post-weld heat treatment may be applied where required by the fabrication code. Forming operations such as bending and rolling of shells are straightforward at this strength level.

Frequently Asked Questions

What standard is SPV235 produced to? SPV235 is specified in JIS G3115, the Japanese standard for steel plates for pressure vessels for intermediate temperature service.

What is the yield strength of SPV235? The minimum yield strength is 235 MPa for plates up to 50 mm thick, 215 MPa for 50 to 100 mm, and 195 MPa for plates over 100 mm thick.

What is the chemical composition of SPV235? For plates up to 100 mm, maximum carbon is 0.18 percent, silicon 0.35 percent, manganese 1.40 percent, and phosphorus and sulfur 0.030 percent each; over 100 mm, carbon rises to 0.20 percent maximum.

What is SPV235 used for? It is used for boiler shells, pressure vessels, and storage equipment operating at moderate pressure and temperature.

Is SPV235 weldable? Yes, it has good weldability with standard processes and matching consumables, with preheating recommended for thick plates.

What is the tensile strength of SPV235? The tensile strength range is 400 to 510 MPa.

Send Inquiry