Knowledge

ASTM A302 Grade D PVQ Plate: Properties and Applications

Jan 30, 2026 Leave a message

ASTM A302 Grade D is a manganese-molybdenum-nickel alloy steel plate designed for welded boilers and pressure vessels, and it is commonly supplied to pressure vessel quality requirements. The grade offers high tensile strength together with good toughness, and it is used in high-temperature, high-pressure applications where a stronger plate than plain carbon steel is required. It is defined under ASTM A302, with the corresponding ASME designation SA-302 Grade D for code construction.

What Is A302 Grade D?

A302 Grade D belongs to the ASTM A302 family of manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates for pressure vessels. The D grade is the highest-alloy member of the family, adding nickel to the manganese-molybdenum base to improve toughness and strength. The steel is produced as killed steel with controlled chemistry, and it is intended for welded construction where the plate must carry significant pressure at moderate to elevated temperature.

The grade is used in the oil, gas, and power generation industries for pressure vessel fabrication, and it is frequently specified with additional quality requirements such as ultrasonic examination and impact testing.

Chemical Composition

The composition of A302 Grade D is controlled to balance strength, toughness, and weldability. Typical limits include:

Carbon: controlled to a low maximum value, with the exact limit depending on plate thickness.

Manganese: in the range of about 1.1 to 1.6 percent, providing strength and hardenability.

Silicon: 0.13 to 0.45 percent, for deoxidation.

Phosphorus: maximum 0.035 percent.

Sulfur: maximum 0.035 percent.

Molybdenum: about 0.45 to 0.60 percent, contributing elevated-temperature strength and creep resistance.

Nickel: about 0.40 to 0.70 percent, improving toughness, particularly at lower temperatures.

The combination of molybdenum and nickel distinguishes Grade D from the lower grades of the A302 family and gives it an excellent balance of high-temperature strength and fracture toughness.

Mechanical Properties

The mechanical requirements of A302 Grade D are defined for the relevant thickness range. Typical values include:

Minimum tensile strength: about 550 MPa (80 ksi), with the tensile range typically extending to about 690 MPa (100 ksi).

Minimum yield strength: about 345 MPa (50 ksi).

Minimum elongation: about 20 percent measured in 50 mm.

Impact toughness: can be specified as a supplementary requirement, with Charpy testing commonly carried out at temperatures such as minus 20, minus 40, or minus 60 degrees Celsius depending on the service conditions.

The grade is suitable for service at moderate to elevated temperature, and its applicable temperature range is generally considered to extend from low-temperature impact-qualified conditions up to about 410 degrees Celsius for continuous pressure service, with the exact allowable values defined by the governing design code. Plates above a moderate thickness are normally supplied in the normalized condition, and normalizing plus tempering is the standard heat treatment for the grade.

Heat Treatment and Inspection

A302 Grade D plates are normally supplied in the normalized condition, and normalizing followed by tempering is commonly applied to develop the required microstructure and mechanical properties. Plates thicker than about 25 mm are generally required to be normalized. Because the material is used in pressure vessel construction, it is often subject to ultrasonic examination to the applicable acceptance criteria, and third-party inspection may be requested for critical projects.

For welding, the grade responds to standard low-alloy steel procedures. Preheating is typically applied in the range of 100 to 150 degrees Celsius to prevent cold cracking, and post-weld heat treatment, usually a stress relief anneal in the range of 595 to 650 degrees Celsius, is applied where required by the fabrication code to reduce residual stress and restore weld toughness. Recommended welding processes include shielded metal arc welding, gas tungsten arc welding, and submerged arc welding with matching low-alloy consumables.

Typical Applications

A302 Grade D is primarily used in pressure-bearing equipment where strength and toughness at elevated temperature are required:

Petrochemical industry: reactors, heat exchangers, separators, spherical storage tanks, and liquefied gas cylinders, in high-temperature, high-pressure, and hydrogen service conditions.

Power generation: boiler drums, superheaters, and reheaters, as well as high-pressure water piping and turbine components in hydropower plants.

Nuclear energy: structural components of nuclear reactor pressure vessels, where excellent toughness and strength support safety and stability.

Other fields: liquefied petroleum gas cylinders and hydrogenation reactors operating in low-temperature and high-pressure environments.

The material resists hydrogen corrosion, high-temperature steam, and a range of chemical media, but it is not intended for strongly corrosive conditions such as concentrated acid or alkali service, where corrosion-resistant alloys would be required.

Frequently Asked Questions

What is A302 Grade D and what is its material classification? 302 Grade D is a low-alloy steel plate primarily composed of carbon, manganese, molybdenum, and nickel. It belongs to the ASTM A302 standard, is classified as a pressure vessel steel, and is designed for high-temperature and pressure-bearing applications.

What is the minimum tensile strength of A302 Grade D? The minimum tensile strength is approximately 550 MPa (80 ksi), with the tensile range typically extending to about 690 MPa for the common thickness range.

What is the yield strength of A302 Grade D? The minimum yield strength is about 345 MPa (50 ksi), with the exact value defined by thickness in the specification.

What heat treatment is A302 Grade D usually subjected to? It is typically supplied in the normalized condition and is often normalized and tempered. Normalizing refines the grain structure, while tempering reduces hardness and improves ductility and impact resistance.

What is the maximum service temperature of A302 Grade D? The grade is designed for moderate to elevated temperature service, with allowable stress values defined by the governing pressure vessel code rather than a single fixed maximum temperature. It maintains structural stability and mechanical properties within its code-approved range.

Is A302 Grade D weldable? Yes, it has good weldability. Recommended methods include shielded metal arc welding, gas tungsten arc welding, and submerged arc welding with matching low-alloy consumables, together with preheating and post-weld heat treatment where required.

What pre-welding preparation is required? The weld area must be cleaned of oil, rust, and oxides, the plate should be preheated to approximately 100 to 150 degrees Celsius to prevent cold cracking, and the surface must be dry and free of contaminants.

What post-weld heat treatment is needed? Post-weld heat treatment usually involves stress relief annealing at approximately 595 to 650 degrees Celsius, held for a time based on thickness and then cooled slowly, to reduce welding residual stress and improve weld toughness.

Send Inquiry