Knowledge

S890Q Quenched and Tempered Steel Sheet: Applications and Performance

Oct 16, 2025 Leave a message

S890Q is a quenched and tempered fine grain structural steel sheet supplied under EN 10025-6, the European standard for hot rolled flat products with high yield strength in the quenched and tempered delivery condition. A minimum yield strength of 890 MPa combined with a tensile strength range of 940-1100 MPa lets designers reduce section thickness and overall steel weight in structures that still have to carry heavy static and dynamic loads. Because the properties are produced at the mill by quenching and tempering, no further heat treatment is needed after fabrication.

What S890Q Quenched and Tempered Steel Sheet Is

S890Q belongs to the group of high strength structural steels whose yield strength is far above that of ordinary carbon grades. The designation combines the minimum yield strength of 890 MPa with the letter Q, which stands for the quenched and tempered delivery condition defined in EN 10025-6. The steel is produced as a fine grain product, so a lean analysis together with a controlled rolling and heat treatment route delivers high strength without sacrificing toughness or weldability.

Standard: EN 10025-6

Delivery condition: quenched and tempered

Minimum yield strength: 890 MPa

Tensile strength: 940-1100 MPa

Minimum elongation: 11%

Impact testing temperature: -20 °C

Typical hardness of the delivered sheet: 300-360 HB

Chemical Composition of EN 10025-6 S890Q

The analysis is deliberately lean. Strength comes from the quench and temper treatment rather than from heavy alloying, which keeps the carbon equivalent low enough for practical welding in a fabricator workshop.

Element Limit (%)
C max 0.20
Si max 0.80
Mn max 1.70
P max 0.025
S max 0.015

Tight phosphorus and sulphur limits reduce centreline segregation and the risk of lamellar tearing in thick welded joints, a point that matters when the sheet is used in heavily loaded connection nodes.

Mechanical Properties of S890Q Steel Sheet

Property Requirement
Tensile strength 940-1100 MPa
Yield strength min 890 MPa
Elongation min 11%
Impact test -20 °C

The narrow spread between yield and tensile strength is the signature of quenched and tempered plate: the material works at a high stress level while keeping enough ductility to redistribute local peaks instead of cracking. Tensile and impact specimens are taken in the rolling direction and the properties are verified on each rolled piece.

How Quenching and Tempering Produce the Performance

Quenching means cooling the plate more rapidly than it would cool in still air. The plate is austenitised and then cooled fast enough to suppress the formation of soft ferrite and pearlite, which produces a hard martensitic or bainitic structure. Tempering follows: the plate is reheated to a controlled temperature below the transformation range so that strength, ductility and toughness reach the required balance. That combination gives S890Q its characteristic profile of very high yield strength with usable elongation and low temperature impact toughness.

Applications of S890Q Steel Sheet

Fabricated bridge, tower and building members. Girders, trusses, columns and support beams benefit from the 890 MPa minimum yield strength, which permits slimmer members and cuts steel weight by roughly 15-20% compared with mild steel, while long term stability under heavy dynamic loads is maintained.

Components for earthmoving and transport equipment. Frames, chassis and load bearing parts of construction and transport machinery use the grade because tensile strength up to 1100 MPa and good fatigue resistance allow repeated high stress cycles without structural failure.

Dipper sticks, buckets and crane booms. Where impact and abrasion are critical, the 300-360 HB hardness of the delivered sheet helps components resist wear and deformation under harsh operating conditions and extends service life.

Turbine scroll cases and unfired pressure vessels. The toughness and ductility of the tempered structure suit pressure containing components that see fluctuating stresses, keeping integrity under cyclic loading.

Penstocks. Hydroelectric penstocks carry water at high pressure; the high tensile strength of S890Q allows wall thickness to be reduced, saving material weight and cost while the section still absorbs hydraulic shock.

Frequently Asked Questions

Q: What does the Q in S890Q mean?
The Q indicates the quenched and tempered delivery condition specified in EN 10025-6, so the mechanical properties are obtained by heat treatment at the mill rather than by the customer.

Q: What is the minimum yield strength of S890Q sheet?
890 MPa, with a tensile strength between 940 and 1100 MPa and a minimum elongation of 11%.

Q: At what temperature is S890Q impact tested?
Charpy impact testing is carried out at -20 °C, which confirms the low temperature toughness needed for outdoor and pressure service.

Q: Can S890Q be welded?
Yes. The grade is produced with a low carbon equivalent and tight sulphur and phosphorus limits so that qualified welding procedures can be applied, with preheat and heat input controlled to protect the tempered microstructure.

Q: What hardness does S890Q plate have?
Delivered sheet normally falls in the 300-360 HB range, which supports wear resistance in buckets, dipper sticks and similar parts.

Q: Which industries use S890Q most?
Bridge and building construction, earthmoving and transport equipment, cranes, hydroelectric penstocks, turbines and pressure vessel fabrication.

Send Inquiry