Reading the W12 x 22 Designation
The letter W identifies a hot-rolled wide flange shape with substantially parallel flange faces, 12 is the nominal depth in inches, and 22 is the nominal mass in pounds per foot, equal to about 32.7 kilograms per metre. Two different standards govern such a beam: ASTM A992 defines the material chemistry and mechanical properties of the steel, while ASTM A6 defines the section dimensions, tolerances and properties. Confusing the two leads to unrealistic expectations, because A992 says nothing about the profile and A6 says nothing about the steel grade. When the nominal depth and the actual depth differ, the actual value in ASTM A6 always governs the design.
Section Dimensions and Properties
The actual dimensions of a W12 x 22 are given below together with the principal section properties used in structural design.
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Depth, d | 312.7 mm | Section area | 4181 mm2 |
| Flange width, bf | 102.4 mm | Mass | 32.7 kg/m |
| Web thickness, tw | 6.6 mm | Moment of inertia, Ix | 64.9 x 10^6 mm4 |
| Flange thickness, tf | 10.8 mm | Elastic section modulus, Sx | 415 x 10^3 mm3 |
| Radius of gyration, rx | 124.6 mm | Moment of inertia, Iy | 6.7 x 10^6 mm4 |
| Radius of gyration, ry | 40.1 mm | Elastic section modulus, Sy | 130 x 10^3 mm3 |
The very large difference between Ix and Iy is characteristic of all W shapes: the beam is roughly ten times stiffer about its strong axis than about its weak axis. Lateral support therefore governs the design of any unbraced beam, because a W12 x 22 loaded about its weak axis is inefficient.
Chemical Composition of ASTM A992
| Element | Requirement |
|---|---|
| Carbon | 0.23% max |
| Manganese | 0.50-1.50% |
| Phosphorus | 0.035% max |
| Sulfur | 0.045% max |
| Silicon | 0.40% max |
| Copper | 0.20% min when copper bearing steel is specified |
| Carbon equivalent | 0.45% max |
The carbon equivalent limit is the reason A992 beams weld without elaborate preheat in normal fabrication conditions. Copper, when specified, improves resistance to atmospheric corrosion and is particularly useful for exposed or offshore members.
Mechanical Properties of A992 Steel
| Property | Requirement |
|---|---|
| Yield strength | 345-450 MPa |
| Tensile strength | 450 MPa min |
| Yield-to-tensile ratio | 0.85 max |
| Elongation | 21% min in 200 mm |
Both a minimum and a maximum yield strength are specified. The upper limit and the yield-to-tensile ratio cap prevent the steel from becoming too strong relative to its ductility, which is essential for structures designed to dissipate energy during an earthquake.
Comparison with Other Common Beam Grades
| Property | ASTM A992 | ASTM A36 | ASTM A572 Grade 50 |
|---|---|---|---|
| Minimum yield strength | 345 MPa | 250 MPa | 345 MPa |
| Maximum yield strength | 450 MPa | Not specified | Not specified |
| Tensile strength range | 450 MPa min | 400-550 MPa | 450 MPa min |
| Carbon equivalent control | 0.45% max | Not specified | Not specified |
| Copper for corrosion resistance | 0.20% min when specified | 0.20% min when specified | Option available |
| Typical use | Building frames, seismic design | General fabrication | General structural steel |
Where W12 x 22 Beams Are Used
Floor and roof framing in low and medium-rise buildings where the 12 inch depth fits within the floor zone.
Secondary beams and purlins spanning short to moderate distances with adequate lateral restraint from the deck.
Crane runway support beams, equipment skids and machinery support platforms in industrial buildings.
Truss chords, bracing members and mezzanine framing in combination with larger columns.
Auxiliary structures such as walkways, platforms and pipe racks, where a copper-bearing option is used for exposed atmospheres.
Because the beam is light, a single member can often be handled by a small crane or an excavator attachment, which reduces erection cost on small projects.
Ordering, Fabrication and Verification
Specify the shape designation, the steel grade, the length and the quantity, and state whether the beam is required in mill lengths or cut to a cutting list. Check the mill certificate for heat number, chemistry, carbon equivalent, yield and tensile results, and elongation. Dimensional verification covers depth, flange width, web and flange thickness, straightness, camber and length. Because W shapes are usually supplied with a protective primer or in the as-rolled condition, confirm the surface treatment before fabrication so that the coating system is compatible with subsequent welding and painting.
Frequently Asked Questions
Q: Is W12 x 22 the same as a 12 inch I-beam?
No. A wide flange shape has parallel flange faces and a wider flange relative to the web, so it carries more bending moment for a similar mass than an American Standard I-beam of the same depth.
Q: Can A992 beams be welded without preheating?
In normal thicknesses, yes, because the carbon equivalent is limited to 0.45%, but thick sections and cold site conditions still require a qualified welding procedure with preheat.
Q: What is the actual weight of a W12 x 22?
Nominal mass is 22 pounds per foot, or about 32.7 kilograms per metre; the exact theoretical mass follows the ASTM A6 section properties.
Q: Why is a maximum yield strength specified for A992?
The cap and the yield-to-tensile ratio limit keep the material ductile and protect the overstrength assumptions used in seismic design.
Q: How does lateral support affect a W12 x 22 beam?
The beam is about ten times stiffer about its strong axis, so its bending capacity is limited by lateral torsional buckling unless the compression flange is restrained.
Q: Which standard gives the section dimensions?
ASTM A6 provides the dimensions, masses, tolerances and section properties of rolled W shapes; ASTM A992 covers only the material requirements.

