What Is 16Mo3 Chrome Moly Steel?
16Mo3 is a low-alloy molybdenum steel plate for boilers and pressure vessels, standardised in EN 10028-2. The grade code signals a nominal carbon content of 0.16% and roughly 0.3% molybdenum, the element that provides creep strength at elevated temperature. Molybdenum raises the recrystallisation temperature of the steel, so components keep their strength in steam service where plain carbon plate would soften.
It should be noted that EN 10028-2, the specification for flat products for pressure purposes, is the correct delivery standard for 16Mo3. EN 10025 covers structural steels and does not define the pressure-equipment requirements that buyers of boiler plate rely on. Ordering 16Mo3 against EN 10028-2 secures the specified chemistry, elevated-temperature properties and impact testing.
The steel combines moderate strength with excellent weldability and good resistance to scaling. Because its alloy content is low, 16Mo3 remains economical while offering a clear performance advantage over carbon-manganese boiler steels in the 350-500 °C band.
Chemical Composition of 16Mo3 Plate
Typical product analysis limits for 16Mo3 are listed below.
| Element | Content (%) |
|---|---|
| C | 0.12-0.20 |
| Si | 0.35 max |
| Mn | 0.40-0.90 |
| P | 0.025 max |
| S | 0.010 max |
| Cr | 0.30 max |
| Mo | 0.25-0.35 |
| Ni | 0.30 max |
| Cu | 0.30 max |
| N | 0.012 max |
The molybdenum range of 0.25-0.35% is the defining feature of the grade. Carbon is capped at 0.20% to keep welding straightforward, and residual elements are limited so that notch toughness is not lost in thick sections.
Mechanical Properties
| Property | To 60 mm | 60-100 mm | 100-150 mm | 150-250 mm |
|---|---|---|---|---|
| Tensile strength Rm (MPa), normalised | 440-590 | 430-580 | 420-570 | 410-570 |
| Tensile strength Rm (MPa), quenched and tempered | 440-570 | 420-550 | - | - |
Charpy V-notch impact requirements at +20 °C are graded with section size, because thicker plate cools more slowly during rolling and heat treatment.
| Condition | Test temperature | Orientation | Min energy |
|---|---|---|---|
| Normalised | +20 °C | Transverse | 27 J |
| Quenched and tempered | +20 °C | Transverse | 34 J |
| Quenched and tempered | +20 °C | Longitudinal | 50 J |
Heat Treatment and Service Range
16Mo3 is normally delivered in the normalised condition at 890-950 °C, and it can also be supplied quenched and tempered when higher strength or better toughness is needed. For quenched and tempered delivery the plate is austenitised at roughly 880-930 °C, quenched in water or oil, then tempered at 650-700 °C.
The grade is applied in steam service up to about 500 °C. Above that temperature the creep strength falls away and higher-alloy grades become the better choice. Cold forming is straightforward, but heavily formed parts benefit from stress-relief annealing at 600-650 °C.
Fabrication and Welding Notes
The low carbon and low alloy content of 16Mo3 give it good weldability compared with higher chromium grades. For plate below about 30 mm thick, welding may be carried out with a modest preheat of 100-150 °C; thicker sections are usually welded with a preheat of 150-200 °C and a controlled interpass temperature. Matching low-alloy molybdenum filler metal maintains strength across the joint.
Post-weld heat treatment at 600-680 °C is applied to relieve stress in heavy or restrained joints. The steel machines and cuts readily, and it responds predictably to bending, so tube plates, shells and dished ends can all be produced from the same plate stock.
Typical Applications
Shells and tube plates of steam boilers and waste heat boilers
Superheater and economiser components
Pressure vessels for steam, hot water and process gas
Headers, manifolds and connecting pipe in power plant
Storage and buffer vessels in chemical and petrochemical plants
Frequently Asked Questions
Q: Which standard defines 16Mo3 plate?
A: 16Mo3 is a pressure-purpose plate grade listed in EN 10028-2, which specifies its chemistry, room-temperature and elevated-temperature properties and testing requirements.
Q: Why is molybdenum added to this steel?
A: Molybdenum in the range of 0.25-0.35% raises the temperature at which the steel loses strength, giving 16Mo3 useful creep resistance in steam service up to about 500 °C.
Q: Is 16Mo3 easy to weld?
A: Yes. Its low carbon and low alloy content make it one of the most weldable elevated-temperature boiler steels, requiring only modest preheat and, for thick sections, post-weld heat treatment.
Q: What is the difference between normalised and quenched and tempered 16Mo3?
A: Both deliver similar tensile strength, but the quenched and tempered condition offers higher impact energy, which is useful where the plate must resist brittle fracture in thick or cold-service components.
Q: Can 16Mo3 be used above 500 °C?
A: Its creep strength declines beyond that point, so applications at higher temperature normally move to chromium-bearing grades with greater elevated-temperature capability.
Q: What forms is the material supplied in?
A: It is available as hot rolled plate in thicknesses up to 250 mm, which covers shells, tube plates, headers and dished ends for boiler and pressure vessel fabrication.

